Husqvarna 13 AWD manual Lubrication of belt tensioner, Rider 13 C, Rider 15 C

Page 45

LUBRICATION

Check the transmission’s oil level

Rider 13 C, Rider 13 AWD and Rider 15 C

1.Lift off the transmission cover. Release the two screws (one of each side) and lift off the trans- mission cover.

2.Rider 13 C, Rider 15 C

Check that there is oil in the transmission oil tank. Top up if necessary with engine oil SAE 10W/30 (class SF–CC).

Rider 13 AWD

Check that there is oil in the transmission oil tank. Top up if necessary with engine oil SAE 10W/40 (class SF–CC).

The oil should be changed by an authorised service workshop, and is described in the Workshop Manual.

The filter is replaced at the same time as changing the oil.

Work on the system entails particular demands on cleanliness and the system must be vented before the machine is used.

Lubrication of belt tensioner

The belt tensioner must be lubricated regularly with high-quality molybdenum sulphide grease*.

Inject grease into the nipple on the right side below the engine bottom pulley until grease is forced out.

With daily use lubrication should be conducted twice a week.

8009-585

6021-030

6008-240H

6008-232

English – 43

Image 45

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads TowingSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brakePresentation Rider 13 C, 13 AWD, 15 C Speed limiterParking brake Lift lever for cutting unit Cutting unitLever for adjustment of cutting height SeatFuelling Before starting DrivingStarting the engine Rider 13 AWDWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryDriving the machine For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C Cutting tips Stopping the engine Hill start, manual gearboxRelease lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningDismantling of the machine hoods Engine hoodFront hood Rider Inspecting the silencer Right-hand fenderLeft-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Main fuse Checking the tyre pressureCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderMaintenance Rider 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Lubrication Check the engine’s oil levelChanging the oil Rider 13 C, Rider 15 C Lubrication of belt tensionerLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Problem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01