Husqvarna 15 C, 13 AWD manual Explanation of Symbols, Slope

Page 6

EXPLANATION OF SYMBOLS

These symbols are on the machine and in the operator’s manual.

Study them carefully so that you know what they mean.

Read the operator’s manual

R	N
Reverse	Neutral	Fast	Slow	Engine off	Battery	Choke	Fuel

Oil pressure

Cutting height

Backwards

Forwards

Ignition

Hydrostatic free wheel

Use hearing protection

Clutch in

Clutch out

Parking brake

Brake

Clutch

Warning

	Noise emission to surround-	Warning! Rotating blades.	Warning! Risk that the	Never drive across	CE conformity marking
	ings in accordance with the	Warning! Rotating blades.	Warning! Risk that the
			machine can tip over
				a slope
	directive of the European


	Community. The machine’s
	emission is indicated in the
	chapter TECHNICAL DATA
	and on the decal.

Never use the machine if persons,	Never carry passengers on
especially children, or animals,	the machine or equipment.
are in the vicinity.

Starting instructions Read the instructions Check the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit

Put the gear shift/hydrostat pedal in neutral

Brake

If the engine is cold use the choke Start the engine

Release the parking brake before driving

Keep hands and feet away	Drive very slowly
from under the hood when	without the cutting unit.
the engine is running.

Speed limiter pedal forwards

Neutral

Speed limiter pedal reverse

Switch off the engine and take off the ignition cable before repairs or maintenance

4– English

Image 6

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Travel and transport on public roads IntroductionDear customer TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Clutch pedal Presentation Rider 11, 11 CThrottle and Choke lever Brake pedal / Parking brakePresentation Rider 13 C, 13 AWD, 15 C Speed limiterParking brake Cutting unit Lift lever for cutting unitLever for adjustment of cutting height SeatFuelling Starting the engine DrivingBefore starting Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderDriving the machine For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engineRear Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerDismantling of the machine hoods Engine hoodFront hood Rider Inspecting the silencer Right-hand fenderLeft-hand fender Checking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Checking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Main fuse Checking the tyre pressureCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugMaintenance Rider 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Lubrication Check the engine’s oil levelChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Trouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 5 hours ServicejournalPre-delivery service Work doneWork done Date, mileage, stamp, sign English 115 01