Husqvarna manual Release lever Rider 13 C, Rider 13 AWD Rider 15 C, Release lever Rider 13 AWD

Page 24

DRIVING

Release lever Rider 13 C, Rider 13 AWD and

Rider 15 C

In order to move the machine when the engine is switched off the release lever must be pressed down and forwards.

Release lever Rider 13 AWD

Rider 13 AWD has one control for the front axle and one control for the rear axle.

Pull the controls to their end positions. Do not use an intermediate position.

Rear Axle

• Control pulled out, drive system disengaged.

• Control pushed in, drive system engaged.

Rider 13 AWD rear

Front Axle

The control is positioned on the inside of the left front wheel.

• Rear control (pulled out), drive system disengaged.

• Front control (pushed in), drive system engaged.

Rider 13 AWD front

8009-574

6021-028

6021-029

22– English

Image 24

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakePresentation Rider 13 C, 13 AWD, 15 C Speed limiterParking brake Cutting unit Lift lever for cutting unitLever for adjustment of cutting height SeatFuelling Driving Before startingStarting the engine Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderDriving the machine For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerDismantling of the machine hoods Engine hoodFront hood Rider Inspecting the silencer Right-hand fenderLeft-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Main fuse Checking the tyre pressureCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugMaintenance Rider 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Lubrication Check the engine’s oil levelChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01