Husqvarna 13 AWD, 15 C manual Servicejournal, Pre-delivery service, After first 5 hours, Work done

Page 53

SERVICEJOURNAL

Work done

Pre-delivery service

1.Top up battery with acid and recharge for four hours.

2.Fit steering wheel, seat and any optional equipment.

3.Adjust cutting unit:

Adjust the lifting springs (the ”weight” of the cutting unit should be 12-15 kg). Only applies to BioClip.

Adjust cutting unit so that rear edge is about 2–4 mm higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5 mm above the frame of the unit at the lowest cutting height.

4.Check that engine has correct amount of oil.

5.Check that the right amount of oil is in the transmission. (Not Rider 11)

6.Check and adjust tyre pressure (60 kPa, 0.6 bar).

7.Connect battery.

8.Fill with fuel and start engine.

9.Check that machine does not move in neutral. (Not Rider 11)

10.Check:

Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lift lever safety switch.

Safety switch for hydrostatic pedals/neutral setting.

11.Check engine revs 2 950 rpm.

12.Tell customer about:

Need and benefits of following the service schedule.

The need and advantages of leaving the machine for regular service.

The effects of maintenance on the machine’s second hand value.

Range of applications for BioClip.

13. Complete proof of sale, etc.

Pre-delivery service carried out.

No outstanding problems.

Certified:

Date, mileage, stamp, sign

After first 5 hours

1. Change engine oil.

Image 53

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads TowingSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSeat Before starting DrivingStarting the engine Rider 13 AWDWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearboxRelease lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01