Husqvarna 13 AWD, 15 C manual Trouble Shooting Schedule, Problem Procedure

Page 47

TROUBLE SHOOTING SCHEDULE

Problem	Procedure

Engine will not start	•	Fuel tank empty
	•	Plug defective
	•	Plug connection defective
	• Dirt in carburettor or fuel pipe

Starter does not pull round engine	•	Battery flat
	• Bad contact between cable and battery terminal
	• Lift lever for cutting unit in wrong position
	• Main fuse blown. The fuse is placed in front of the
		battery, under the battery cover.
	•	Ignition lock faulty
	• Gear shift/hydrostat pedal not in neutral

Engine does not run smoothly	•	Wrong gear, too high
	•	Carburettor incorrectly set
	•	Air filter clogged
	• Fuel tank vent blocked
	•	Ignition setting defective
	• Dirt in fuel pipe
	• Choke activated or throttle wire incorrectly adjusted

Engine seems to have no power	•	Air filter clogged
	•	Plug defective
	• Dirt in carburettor or fuel pipe
	•	Carburettor incorrectly set
	• Choke activated or throttle wire incorrectly adjusted

Engine overheats	•	Engine overloaded
	• Air intake or cooling flanges blocked
	•	Fan damaged
	• Too little or no oil in engine
	•	Ignition defective
	•	Plug defective

Battery does not charge	•	One or more cells faulty
	• Bad contact between battery terminals and cables.

Machine vibrates	•	Blades are loose
	•	Engine is loose
	• Imbalance on one or more blades, resulting from
		damage or inferior balancing after sharpening

Uneven mowing	•	Blades blunt
	•	Cutting unit skew
	• Long or wet grass
	• Grass blockage under hood
	• Different tyre pressures on right and left sides
	•	Over-speeding
	•	Drive belts slipping

English – 45

Image 47

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Towing IntroductionDear customer Travel and transport on public roadsSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Brake pedal / Parking brake Presentation Rider 11, 11 CThrottle and Choke lever Clutch pedalParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSeat Rider 13 AWD DrivingBefore starting Starting the engineWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearboxFront Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Rear AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Checking the brake Rider 11 and Rider 11 C Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Poorly adjusted brakes can result in reduced braking powerAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting ScheduleCover ServiceStorage Winter storageTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service After first 5 hoursWork done Date, mileage, stamp, sign English 115 01