Husqvarna 15 C, 13 AWD To start an engine with a weak battery, To remove cables, reverse order

Page 20

DRIVING

7.When the engine has started release the igni- tion key to neutral position.

Push the throttle control to the required speed. For cutting 3/4 to full throttle.

WARNING!

Never run the engine indoors, in enclosed or poorly ventilated areas. The exhaust fumes contain toxic carbon monoxide.

STOP START

6007-007

To start an engine with a weak battery

WARNING!

Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged.

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT INFORMATION

Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower battery to start other vehicles.

To attach jumper cables

•Connect each end of the RED cable to the

POSITIVE (+) terminal on each battery, taking care not to short against chassis.

• Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

• Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from the fuel tank and battery.

To remove cables, reverse order

•BLACK cable first from chassis and then from the fully charged battery.

Jumper cables connection

•RED cable last from both batteries.

18– English

8011-642

Image 20

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Cutting unit Lift lever for cutting unitFuelling Lever for adjustment of cutting heightSeat Driving Before startingStarting the engine Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Changing the oil LubricationCheck the engine’s oil level Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01