Husqvarna 15 C manual Adjusting the Parking Brake Rider 13 AWD

Page 31

MAINTENANCE

Adjusting the Parking Brake Rider 13 AWD

Check that the parking brake is adjusted correctly by placing the machine on a slope with the front and rear axles disengaged. Apply and lock the parking brake. When the machine does not stand still, the parking brake should be adjusted accord- ing to the following.

1. Remove the left-hand wing cover.

2. Release the lock nuts (1).

3. Tension the wire with the adjusting screw (2) until all the play in the wire is taken up.

4.Tighten the lock nuts (1).

5.On completion of the adjustment the brake should be re-checked.

6. Assemble the left-hand wing cover.

WARNING!

A poorly adjusted parking brake can result in reduced braking ability.

8009-501

6021-031

English – 29

Image 31

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Towing IntroductionDear customer Travel and transport on public roadsSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Brake pedal / Parking brake Presentation Rider 11, 11 CThrottle and Choke lever Clutch pedalSpeed limiter Presentation Rider 13 C, 13 AWD, 15 CParking brake Lift lever for cutting unit Cutting unitSeat Lever for adjustment of cutting heightFuelling Rider 13 AWD DrivingBefore starting Starting the engineWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryFor Rider 13 C, Rider 13 AWD and Rider 15 C Driving the machineFor Rider 11 and Rider 11 C Cutting tips Stopping the engine Hill start, manual gearboxFront Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Rear AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningEngine hood Dismantling of the machine hoodsFront hood Rider Right-hand fender Inspecting the silencerLeft-hand fender Checking and adjustment of the steering wires Checking the brake Rider 11 and Rider 11 C Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Poorly adjusted brakes can result in reduced braking powerAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Rider 13 AWD Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderService position for BioClip Maintenance Rider 11C,13C, 13 AWD,15CPlacing in service position 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Check the engine’s oil level LubricationChanging the oil Rider 13 C, Rider 15 C Lubrication of belt tensionerGeneral lubrication Lubrication Rider 11 and Rider 11 CLubrication of front wheel bearings Problem Procedure Trouble Shooting ScheduleCover ServiceStorage Winter storageTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service After first 5 hoursWork done Date, mileage, stamp, sign English 115 01