Husqvarna 13 AWD, 15 C Hill start, manual gearbox, Stopping the engine

Page 23

DRIVING
WARNING!
Never drive the machine on
ground with a slope of more than
15°. Mow slopes upwards and
downwards, never across. Avoid
sudden changes in direction.
Hill start, manual gearbox
1. Press down the parking brake.
2. Push the throttle control to full throttle position.	MAX 15°
3. Push down the clutch and engage first gear.
4. Carefully release the clutch.
5. When the engine starts to pull, release the	6007-013
5. When the engine starts to pull, release the
parking brake.
Stopping the engine
Preferably allow the engine to idle for a minute to
obtain normal working temperature before stopping
it if it has been working hard.
1. Lift up the cutting unit by pulling the lever back to
the end position.
	6007-014H

2.Rider 11 and Rider 11 C: Pull back the throttle control and put the gear lever into neutral ”N” without pressing the reverse lock button. Turn the ignition key to the ”STOP” position.

Rider 13 C and Rider 15 C: Pull back the throttle lever and turn the ignition key to the ”STOP” position.

3.When the rider mower is stationary, hold down the parking brake and push in the lock button.

STOP	START
	6007-015

English – 21

Image 23

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Towing IntroductionDear customer Travel and transport on public roadsSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Brake pedal / Parking brake Presentation Rider 11, 11 CThrottle and Choke lever Clutch pedalParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSeat Rider 13 AWD DrivingBefore starting Starting the engineWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearboxFront Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Rear AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Checking the brake Rider 11 and Rider 11 C Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Poorly adjusted brakes can result in reduced braking powerAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting ScheduleCover ServiceStorage Winter storageTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service After first 5 hoursWork done Date, mileage, stamp, sign English 115 01