Husqvarna 15 C, 13 AWD manual Inspecting the silencer, Right-hand fender, Left-hand fender

Page 28

MAINTENANCE

Right-hand fender

Remove the screws (2 and 3) from the fender. On the Rider 13 C, Rider 13 AWD and Rider 15 C the knob (1) must also be removed.

	3
11	2
11
	8009-576

Left-hand fender

Release the screws in the fender and lift off the fender.

8009-577

Inspecting the silencer

Check regularly that the silencer is complete and secured correctly.

Temperature variations and vibrations can mean that the tightening torque for the screws drops. The screws should be checked when servicing to guarantee the correct torque. The tightening torque should be about 10 Nm. Never use a defective silencer.

WARNING!

The mufﬂer gets very hot in use and remains so for a short time afterwards. Contact can result in burns. Remember the risk of ﬁre.

8009-683

26– English

Image 28

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakeSpeed limiter Presentation Rider 13 C, 13 AWD, 15 CParking brake Cutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Driving Before startingStarting the engine Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderFor Rider 13 C, Rider 13 AWD and Rider 15 C Driving the machineFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerEngine hood Dismantling of the machine hoodsFront hood Rider Right-hand fender Inspecting the silencerLeft-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugService position for BioClip Maintenance Rider 11C,13C, 13 AWD,15CPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Check the engine’s oil level LubricationChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 CGeneral lubrication Lubrication Rider 11 and Rider 11 CLubrication of front wheel bearings Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01