Husqvarna 15 C, 13 AWD manual Adjustment of the throttle wire, Replacement of the fuel filter

Page 32

MAINTENANCE

Adjustment of the throttle wire

If the engine does not respond as it should when the throttle lever is moved, or if it produces black smoke or does not reach top speed, the throttle wire may need adjusting.

1.Release the clamping screw (see arrow) and push the throttle control to the choke position.

2.Pull the throttle wire’s outer casing to the far right and check that the choke is fully activated.

3.Tighten the clamping screw.

4.Pull the throttle control back to the full throttle position and check that the choke is no longer activated.

Replacement of the fuel filter

Replace the pipe fitted fuel filter every 100 running hours (once per season) or more frequently if it is clogged.

Replace the filter as follows:

1.Raise the engine cover.

2.Move the hose clips away from the filter. Use a pair of flat pliers.

3.Pull off the filter from the hose ends.

4.Press in the new filter on the hose ends. If necessary soap solution can be applied on the filter ends to simplify fitting.

5.Push the hose clips back on the filter.

30– English

8009-402

8009-403

8009-404

8009-405

Image 32

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Cutting unit Lift lever for cutting unitFuelling Lever for adjustment of cutting heightSeat Driving Before startingStarting the engine Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Changing the oil LubricationCheck the engine’s oil level Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01