Husqvarna 1153136-49 manuel dutilisation Fuel Handling

Page 19

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

 

 

Gasoline

•Use good quality unleaded gasoline.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures. Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•We recommend the use of special oil (chain oil) with good adhesion characteristics. (48)

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 0°C (32°F) some oils become too viscous.This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

1153136-49 Rev.2 2010-04-08

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 1153136-49 Rev.2 445 445e 450 450e1153136-49 Rev.2 3839 4243 1153136-49 Rev.2 102 Symbols on the machine and/or in the manual KEY to SymbolsAir purge Adjustment of the oil pump 1153136-49 Rev.2 Canada You will find the following labels on your chain sawContents Introduction What is what on the chain saw?Dear customer Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Throttle lockout Chain brake and front hand guardChain catcher Cutting equipment Sharpening your chain and adjusting depth gauge setting Lubricating cutting equipment Tensioning the chainChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubrication445e, 450e AssemblyFitting the bar and chain 445Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageStopping Starting and StoppingStarting and stopping StartingGeneral working instructions Basic safety rulesWorking Techniques Before useTerms Basic cutting techniqueLimbing Tree felling technique What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Carburetor adjustment MaintenanceGeneral Starter MufflerReplacing the starter cord Needle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleMore even wear. Check Technical data Technical Data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges Recommended cutting equipment for CanadaYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPompe à carburant Réglage de la pompe à huile Explication DES SymbolesSymboles sur la machine et/ou dans le manuel Décompresseur LeEPA Sommaire SommaireConsignes de sécurité pour les utilisateurs de Quels sont les composants de la tronçonneuse? Cher clientAVERTISSEMENT! Ne jamais modifier Instructions Générales DE SécuritéAVERTISSEMENT! Utilisée de manière Équipement de protection personnelle Utilisez toujours votre bon sensFrein de chaîne avec arceau protecteur Équipement de sécurité de la machineSystème anti-vibrations Blocage de l’accélérationCapteur de chaîne Protection de la main droiteAffûtage et réglage de l’épaisseur du copeau de la chaîne Équipement de coupeRègles élémentaires Équipement de coupe anti-rebondGénéralités sur le réglage de l’épaisseur du copeau Tension de la chaîneContrôle de la lubrification de la chaîne Lubrification de l’équipement de coupeLibérer le bouton en le dépliant Remplissage d’huile de chaîneAVERTISSEMENT! La plupart des Pignon d’entraînementGraissage du roulement à aiguilles Contrôle de l’usure de l’équipement de coupePour toute manipulation de la chaîne MontageMontage du guide-chaîne et de la chaîne AVERTISSEMENT! Utiliser des gantsCarburant Manipulation DU CarburantRemisage prolongé Remplissage de carburantSécurité carburant Transport et rangementDémarrage et arrêt Démarrage ET ArrêtDémarrage Arrêt Règles élémentaires de sécurité Techniques DE TravailAvant chaque utilisation Méthodes de travailGénéralités Technique de base pour la coupeLâcher les poignées AVERTISSEMENT! N’utilisez jamais uneSens d’abattage Techniques d’abattageÉlagage Distance de sécuritéSolution à un abattage raté Qu’est-ce qu’un rebond? Mesures anti-rebondTronçonnage en rondins Généralités EntretienRéglage du carburateur Silencieux Remplacement de la corde du lanceurLanceur Montage du lanceur Filtre à airBougie Mise sous tension du ressortÉpuration centrifuge Air Injection Graissage du pignon d’entraînement du guideGraissage du roulement à aiguilles Système de refroidissementInspecter tous les câbles et Schéma d’entretienEst en bon état, le remplacer si ’embrayageCaractéristiques Techniques Équipement de coupe recommandé pour CanadaCaractéristiques techniques Affûtage de la chaîne et gabarits d’affûtage Combinaisons guide-chaîne et chaîneVOS Droits ET Obligations EN Garantie Demande D’INDEMNITÉ Service APRÈS-VENTE AVERTISSEMENT! N’utilisez pas une Précautions à prendre pour se protéger des rebondsAutres consignes de sécurité Ansi B175.1-2000 Annexe CPrécautions Sécuritaires Conformant AUX Normes Américaines Símbolos en la máquina en/o el manual de instrucciones Aclaracion DE LOS SimbolosBomba de combustible Ajuste de la bomba de aceite Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante ¡ATENCION! La mayoría de los Equipo de protección personalEquipo de seguridad de la máquina Freno de cadena con protección contra reculadasSistema amortiguador de vibraciones Fiador del aceleradorCaptor de cadena Protección de la mano derechaReglas básicas Equipo de corteBotón de parada SilenciadorGeneralidades sobre el afilado de los dientes cortantes CadenaGeneralidades sobre el ajuste de la profundidad de corte Repostaje de aceite para cadena de motosierra Tensado de la cadenaLubricación del equipo de corte Ajuste de la profundidad de corteLubricación del cojinete de agujas Control de la lubricación de la cadenaSi no funciona la lubricación de la cadena Piñón de arrastre de la cadena¡ATENCION! Para manipular la cadena MontajeMontaje de la espada y la cadena Montaje del apoyo de cortezaCarburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamientoNunca enrosque el cordón de arranque alrededor de la mano Arranque Y ParadaArranque y parada ArranqueParada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoDesignaciones Técnica básica de corteDirección de derribo Técnica de talaDesramado Distancia de seguridadTratamiento de una tala fallida ¿Qué es la reculada? Medidas preventivas de las reculadasTronzado del tronco Generalidades MantenimientoAjuste del carburador Mecanismo de arranque SilenciadorCambio del cordón de arranque Bujía Filtro de aireEngrase del cabezal de rueda de la espada Utilización en invierno Lubricación del cojinete de agujasSistema refrigerante Depuración centrífuga Air InjectionCompruebe si están desgastados el Programa de mantenimientoLimpie el filtro de aire. Cámbielo si es Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Garantia DEL Sistema DE Control DE EmisionesLista DE Componentes DE LA Garantia DE Control DE Emisiones Otras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadasPrecauciones DE Seguridad DE LA Norma Americana ´z+U-¶2a¨ ´z+U-¶2a¨

1153136-49 specifications

The Husqvarna 1153136-49 is a reliable and high-performance chainsaw specifically designed for homeowners and occasional users who seek both power and ease of use. Its construction reflects Husqvarna's reputation for quality and innovation, making it a preferred choice among enthusiasts and those needing practical tools for yard and garden maintenance.

One of the standout features of the 1153136-49 is its powerful engine. It is equipped with a sturdy and efficient 50.2cc X-Torq engine, which delivers excellent power output while minimizing fuel consumption and emissions. This means users can enjoy extended operation time with reduced environmental impact, which is increasingly important in today’s eco-conscious world.

The chainsaw boasts an impressive cutting length, making it suitable for a variety of tasks, from pruning branches to cutting firewood. With a bar length of 18 inches, it provides the versatility needed for light to medium-duty jobs, enabling users to tackle projects around their homes and gardens with ease.

Husqvarna has designed the 1153136-49 with user comfort and safety in mind. It features an ergonomic handle with a soft grip that reduces vibrations, allowing for longer periods of use without discomfort. The chainsaw also includes an advanced anti-vibration system, ensuring a smoother operation that minimizes strain on the user’s hands and arms.

Safety is paramount when using a chainsaw, and Husqvarna has integrated several key safety features in the 1153136-49. It comes with a chain brake that stops the chain in case of kickback, as well as low kickback chains that further enhance user safety during operation. The quick-release air filter simplifies maintenance and ensures optimal engine performance.

Another innovative feature is the tool-less chain tensioning system, which allows for easy adjustments on the go, ensuring that the chain remains tight and secure during use. This design not only saves time but also enhances overall safety.

In conclusion, the Husqvarna 1153136-49 is a powerful, efficient, and user-friendly chainsaw packed with features that enhance performance and safety. It is an ideal choice for homeowners and anyone looking to manage their outdoor tasks effectively. With a strong engine, ergonomic design, and safety features, it represents a smart investment for maintaining gardens and outdoor spaces.
Top Page Image Contents