Husqvarna 1153136-49 manuel dutilisation Muffler, Starter, Replacing the starter cord

Page 27

MAINTENANCE

Throttle lockout

•Make sure the throttle control is locked at the idle setting when the throttle lockout is released. (95)

•Press the throttle lockout and make sure it returns to its original position when you release it. (96)

•Check that the throttle control and throttle lockout move freely and that the return springs work properly.

(97)

•Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburetor idle adjustment.

Chain catcher

Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw. (98)

Right hand guard

Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. (11)

Vibration damping system

Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit. (99)

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting. (53)

NB! The start/stop switch automatically returns to run position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine. (100)

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week.This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective. (13)

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Replacing the starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter. (101)

•Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards. (102)

•Undo the bolt in the centre of the pulley and remove the drive disc (A), drive disc spring (B) and the pulley

(C). Insert and secure a new starter cord in the starter pulley. Wind approx. 3 turns of the starter cord on the starter pulley. Fit the starter pulley so that the end of the recoil spring (D) hooks into the starter pulley. Now assemble the drive disc spring, drive disc and the bolt in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Tie a good knot on the starter cord. (103)

1153136-49 Rev.2 2010-04-08

English – 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 1153136-49 Rev.2 445 445e 450 450e1153136-49 Rev.2 3839 4243 1153136-49 Rev.2 102 KEY to Symbols Symbols on the machine and/or in the manualAir purge Adjustment of the oil pump 1153136-49 Rev.2 Canada You will find the following labels on your chain sawContents What is what on the chain saw? IntroductionDear customer Before using a new chain saw General Safety PrecautionsMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guard Throttle lockoutChain catcher Cutting equipment Sharpening your chain and adjusting depth gauge setting Lubricating cutting equipment Tensioning the chainChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubrication445e, 450e AssemblyFitting the bar and chain 445Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageStopping Starting and StoppingStarting and stopping StartingGeneral working instructions Basic safety rulesWorking Techniques Before useBasic cutting technique TermsLimbing Tree felling technique How to avoid kickback What is kickback?Freeing a tree that has fallen badly Maintenance Carburetor adjustmentGeneral Muffler StarterReplacing the starter cord Needle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceMore even wear. Check Technical data Technical Data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges Recommended cutting equipment for CanadaYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPompe à carburant Réglage de la pompe à huile Explication DES SymbolesSymboles sur la machine et/ou dans le manuel Décompresseur LeEPA Sommaire SommaireConsignes de sécurité pour les utilisateurs de Quels sont les composants de la tronçonneuse? Cher clientInstructions Générales DE Sécurité AVERTISSEMENT! Ne jamais modifierAVERTISSEMENT! Utilisée de manière Équipement de protection personnelle Utilisez toujours votre bon sensFrein de chaîne avec arceau protecteur Équipement de sécurité de la machineSystème anti-vibrations Blocage de l’accélérationCapteur de chaîne Protection de la main droiteAffûtage et réglage de l’épaisseur du copeau de la chaîne Équipement de coupeRègles élémentaires Équipement de coupe anti-rebondGénéralités sur le réglage de l’épaisseur du copeau Tension de la chaîneContrôle de la lubrification de la chaîne Lubrification de l’équipement de coupeLibérer le bouton en le dépliant Remplissage d’huile de chaîneAVERTISSEMENT! La plupart des Pignon d’entraînementGraissage du roulement à aiguilles Contrôle de l’usure de l’équipement de coupePour toute manipulation de la chaîne MontageMontage du guide-chaîne et de la chaîne AVERTISSEMENT! Utiliser des gantsCarburant Manipulation DU CarburantRemisage prolongé Remplissage de carburantSécurité carburant Transport et rangementDémarrage ET Arrêt Démarrage et arrêtDémarrage Arrêt Règles élémentaires de sécurité Techniques DE TravailAvant chaque utilisation Méthodes de travailGénéralités Technique de base pour la coupeLâcher les poignées AVERTISSEMENT! N’utilisez jamais uneSens d’abattage Techniques d’abattageÉlagage Distance de sécuritéSolution à un abattage raté Mesures anti-rebond Qu’est-ce qu’un rebond?Tronçonnage en rondins Entretien GénéralitésRéglage du carburateur Remplacement de la corde du lanceur SilencieuxLanceur Montage du lanceur Filtre à airBougie Mise sous tension du ressortÉpuration centrifuge Air Injection Graissage du pignon d’entraînement du guideGraissage du roulement à aiguilles Système de refroidissementInspecter tous les câbles et Schéma d’entretienEst en bon état, le remplacer si ’embrayageÉquipement de coupe recommandé pour Canada Caractéristiques TechniquesCaractéristiques techniques Affûtage de la chaîne et gabarits d’affûtage Combinaisons guide-chaîne et chaîneVOS Droits ET Obligations EN Garantie Demande D’INDEMNITÉ Service APRÈS-VENTE AVERTISSEMENT! N’utilisez pas une Précautions à prendre pour se protéger des rebondsAutres consignes de sécurité Ansi B175.1-2000 Annexe CPrécautions Sécuritaires Conformant AUX Normes Américaines Aclaracion DE LOS Simbolos Símbolos en la máquina en/o el manual de instruccionesBomba de combustible Ajuste de la bomba de aceite Etiquetas que se encuentran en la motosierra Indice ÍndicePrecauciones de seguridad para usuarios de Introduccion Apreciado cliente¿Qué es qué en la motosierra? Instrucciones Generales DE Seguridad Medidas a tomar antes de utilizar una motosierra nuevaImportante ¡ATENCION! La mayoría de los Equipo de protección personalEquipo de seguridad de la máquina Freno de cadena con protección contra reculadasSistema amortiguador de vibraciones Fiador del aceleradorCaptor de cadena Protección de la mano derechaReglas básicas Equipo de corteBotón de parada SilenciadorCadena Generalidades sobre el afilado de los dientes cortantesGeneralidades sobre el ajuste de la profundidad de corte Repostaje de aceite para cadena de motosierra Tensado de la cadenaLubricación del equipo de corte Ajuste de la profundidad de corteLubricación del cojinete de agujas Control de la lubricación de la cadenaSi no funciona la lubricación de la cadena Piñón de arrastre de la cadena¡ATENCION! Para manipular la cadena MontajeMontaje de la espada y la cadena Montaje del apoyo de cortezaCarburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamientoNunca enrosque el cordón de arranque alrededor de la mano Arranque Y ParadaArranque y parada ArranqueParada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoDesignaciones Técnica básica de corteDirección de derribo Técnica de talaDesramado Distancia de seguridadTratamiento de una tala fallida Medidas preventivas de las reculadas ¿Qué es la reculada?Tronzado del tronco Mantenimiento GeneralidadesAjuste del carburador Silenciador Mecanismo de arranqueCambio del cordón de arranque Filtro de aire BujíaEngrase del cabezal de rueda de la espada Utilización en invierno Lubricación del cojinete de agujasSistema refrigerante Depuración centrífuga Air InjectionPrograma de mantenimiento Compruebe si están desgastados elLimpie el filtro de aire. Cámbielo si es Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Garantia DEL Sistema DE Control DE EmisionesLista DE Componentes DE LA Garantia DE Control DE Emisiones Otras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadasPrecauciones DE Seguridad DE LA Norma Americana ´z+U-¶2a¨ ´z+U-¶2a¨

1153136-49 specifications

The Husqvarna 1153136-49 is a reliable and high-performance chainsaw specifically designed for homeowners and occasional users who seek both power and ease of use. Its construction reflects Husqvarna's reputation for quality and innovation, making it a preferred choice among enthusiasts and those needing practical tools for yard and garden maintenance.

One of the standout features of the 1153136-49 is its powerful engine. It is equipped with a sturdy and efficient 50.2cc X-Torq engine, which delivers excellent power output while minimizing fuel consumption and emissions. This means users can enjoy extended operation time with reduced environmental impact, which is increasingly important in today’s eco-conscious world.

The chainsaw boasts an impressive cutting length, making it suitable for a variety of tasks, from pruning branches to cutting firewood. With a bar length of 18 inches, it provides the versatility needed for light to medium-duty jobs, enabling users to tackle projects around their homes and gardens with ease.

Husqvarna has designed the 1153136-49 with user comfort and safety in mind. It features an ergonomic handle with a soft grip that reduces vibrations, allowing for longer periods of use without discomfort. The chainsaw also includes an advanced anti-vibration system, ensuring a smoother operation that minimizes strain on the user’s hands and arms.

Safety is paramount when using a chainsaw, and Husqvarna has integrated several key safety features in the 1153136-49. It comes with a chain brake that stops the chain in case of kickback, as well as low kickback chains that further enhance user safety during operation. The quick-release air filter simplifies maintenance and ensures optimal engine performance.

Another innovative feature is the tool-less chain tensioning system, which allows for easy adjustments on the go, ensuring that the chain remains tight and secure during use. This design not only saves time but also enhances overall safety.

In conclusion, the Husqvarna 1153136-49 is a powerful, efficient, and user-friendly chainsaw packed with features that enhance performance and safety. It is an ideal choice for homeowners and anyone looking to manage their outdoor tasks effectively. With a strong engine, ergonomic design, and safety features, it represents a smart investment for maintaining gardens and outdoor spaces.
Top Page Image Contents