Husqvarna 1153136-49 manuel dutilisation Air filter, Spark plug, Lubricating the bar tip sprocket

Page 28

MAINTENANCE

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out. (104)

Stretch the line with the handle. Move your thumb and release the line. See the figure below. (105)

Replacing the return and drive springs

Recoil spring (A)

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

•Remove the cassette with the recoil spring from the starter.

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Drive disc spring (B)

•Undo the bolt in the centre of the pulley and remove the drive disc and the drive disc spring.

•Replace the drive disc spring and fit the drive disc above the spring. (106)

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it. (107)

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary. (108)

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

(109)

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly.

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates. (110)

28 – English

1153136-49 Rev.2 2010-04-08

Page 27 Page 29
Image 28
Page 27 Page 29
Contents 445 445e 450 450e 1153136-49 Rev.21153136-49 Rev.2 3839 4243 1153136-49 Rev.2 102 Symbols on the machine and/or in the manual KEY to SymbolsAir purge Adjustment of the oil pump 1153136-49 Rev.2 You will find the following labels on your chain saw CanadaContents Introduction What is what on the chain saw?Dear customer General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipmentPersonal protective equipment Throttle lockout Chain brake and front hand guardChain catcher Cutting equipment Sharpening your chain and adjusting depth gauge setting Tensioning the chain Lubricating cutting equipmentChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chain445 445e, 450eFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingStarting StoppingBasic safety rules Working TechniquesBefore use General working instructionsTerms Basic cutting techniqueLimbing Tree felling technique What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Carburetor adjustment MaintenanceGeneral Starter MufflerReplacing the starter cord Air filter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature -5C 23F or colderCooling system Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleMore even wear. Check Technical Data Technical dataBar and chain combinations Saw chain filing and file gaugesRecommended cutting equipment for Canada 050/1,3 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsExplication DES Symboles Symboles sur la machine et/ou dans le manuelDécompresseur Le Pompe à carburant Réglage de la pompe à huileEPA Sommaire SommaireConsignes de sécurité pour les utilisateurs de Cher client Quels sont les composants de la tronçonneuse?AVERTISSEMENT! Ne jamais modifier Instructions Générales DE SécuritéAVERTISSEMENT! Utilisée de manière Utilisez toujours votre bon sens Équipement de protection personnelleÉquipement de sécurité de la machine Frein de chaîne avec arceau protecteurBlocage de l’accélération Capteur de chaîneProtection de la main droite Système anti-vibrationsÉquipement de coupe Règles élémentairesÉquipement de coupe anti-rebond Affûtage et réglage de l’épaisseur du copeau de la chaîneTension de la chaîne Généralités sur le réglage de l’épaisseur du copeauLubrification de l’équipement de coupe Libérer le bouton en le dépliantRemplissage d’huile de chaîne Contrôle de la lubrification de la chaînePignon d’entraînement Graissage du roulement à aiguillesContrôle de l’usure de l’équipement de coupe AVERTISSEMENT! La plupart desMontage Montage du guide-chaîne et de la chaîneAVERTISSEMENT! Utiliser des gants Pour toute manipulation de la chaîneManipulation DU Carburant CarburantRemplissage de carburant Sécurité carburantTransport et rangement Remisage prolongéDémarrage et arrêt Démarrage ET ArrêtDémarrage Arrêt Techniques DE Travail Avant chaque utilisationMéthodes de travail Règles élémentaires de sécuritéTechnique de base pour la coupe Lâcher les poignéesAVERTISSEMENT! N’utilisez jamais une GénéralitésTechniques d’abattage ÉlagageDistance de sécurité Sens d’abattageSolution à un abattage raté Qu’est-ce qu’un rebond? Mesures anti-rebondTronçonnage en rondins Généralités EntretienRéglage du carburateur Silencieux Remplacement de la corde du lanceurLanceur Filtre à air BougieMise sous tension du ressort Montage du lanceurGraissage du pignon d’entraînement du guide Graissage du roulement à aiguillesSystème de refroidissement Épuration centrifuge Air InjectionSchéma d’entretien Est en bon état, le remplacer si’embrayage Inspecter tous les câbles etCaractéristiques Techniques Équipement de coupe recommandé pour CanadaCaractéristiques techniques Combinaisons guide-chaîne et chaîne Affûtage de la chaîne et gabarits d’affûtageVOS Droits ET Obligations EN Garantie Demande D’INDEMNITÉ Service APRÈS-VENTE Précautions à prendre pour se protéger des rebonds Autres consignes de sécuritéAnsi B175.1-2000 Annexe C AVERTISSEMENT! N’utilisez pas unePrécautions Sécuritaires Conformant AUX Normes Américaines Símbolos en la máquina en/o el manual de instrucciones Aclaracion DE LOS SimbolosBomba de combustible Ajuste de la bomba de aceite Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Equipo de protección personal Equipo de seguridad de la máquinaFreno de cadena con protección contra reculadas ¡ATENCION! La mayoría de losFiador del acelerador Captor de cadenaProtección de la mano derecha Sistema amortiguador de vibracionesEquipo de corte Botón de paradaSilenciador Reglas básicasGeneralidades sobre el afilado de los dientes cortantes CadenaGeneralidades sobre el ajuste de la profundidad de corte Tensado de la cadena Lubricación del equipo de corteAjuste de la profundidad de corte Repostaje de aceite para cadena de motosierraControl de la lubricación de la cadena Si no funciona la lubricación de la cadenaPiñón de arrastre de la cadena Lubricación del cojinete de agujasMontaje Montaje de la espada y la cadenaMontaje del apoyo de corteza ¡ATENCION! Para manipular la cadenaManipulacion DEL Combustible CarburanteRepostaje Seguridad en el uso del combustibleTransporte y almacenamiento Almacenamiento prolongadoArranque Y Parada Arranque y paradaArranque Nunca enrosque el cordón de arranque alrededor de la manoParada Tecnica DE Trabajo Antes de utilizar la máquinaInstrucciones generales de trabajo Reglas básicas de seguridadTécnica básica de corte DesignacionesTécnica de tala DesramadoDistancia de seguridad Dirección de derriboTratamiento de una tala fallida ¿Qué es la reculada? Medidas preventivas de las reculadasTronzado del tronco Generalidades MantenimientoAjuste del carburador Mecanismo de arranque SilenciadorCambio del cordón de arranque Bujía Filtro de aireEngrase del cabezal de rueda de la espada Lubricación del cojinete de agujas Sistema refrigeranteDepuración centrífuga Air Injection Utilización en inviernoCompruebe si están desgastados el Programa de mantenimientoLimpie el filtro de aire. Cámbielo si es Datos Tecnicos Datos técnicosCombinaciones de espada y cadena Afilado y calibres de afilado de la cadena de sierraGarantia DEL Sistema DE Control DE Emisiones SUS Derechos Y Obligaciones DE GarantiaLista DE Componentes DE LA Garantia DE Control DE Emisiones Precauciones DE Seguridad DE LA Norma Americana Precauciones de seguridad para usuarios de motosierrasPrecauciones de seguridad en reculadas Otras precauciones de seguridadPrecauciones DE Seguridad DE LA Norma Americana ´z+U-¶2a¨ ´z+U-¶2a¨

1153136-49 specifications

The Husqvarna 1153136-49 is a reliable and high-performance chainsaw specifically designed for homeowners and occasional users who seek both power and ease of use. Its construction reflects Husqvarna's reputation for quality and innovation, making it a preferred choice among enthusiasts and those needing practical tools for yard and garden maintenance.

One of the standout features of the 1153136-49 is its powerful engine. It is equipped with a sturdy and efficient 50.2cc X-Torq engine, which delivers excellent power output while minimizing fuel consumption and emissions. This means users can enjoy extended operation time with reduced environmental impact, which is increasingly important in today’s eco-conscious world.

The chainsaw boasts an impressive cutting length, making it suitable for a variety of tasks, from pruning branches to cutting firewood. With a bar length of 18 inches, it provides the versatility needed for light to medium-duty jobs, enabling users to tackle projects around their homes and gardens with ease.

Husqvarna has designed the 1153136-49 with user comfort and safety in mind. It features an ergonomic handle with a soft grip that reduces vibrations, allowing for longer periods of use without discomfort. The chainsaw also includes an advanced anti-vibration system, ensuring a smoother operation that minimizes strain on the user’s hands and arms.

Safety is paramount when using a chainsaw, and Husqvarna has integrated several key safety features in the 1153136-49. It comes with a chain brake that stops the chain in case of kickback, as well as low kickback chains that further enhance user safety during operation. The quick-release air filter simplifies maintenance and ensures optimal engine performance.

Another innovative feature is the tool-less chain tensioning system, which allows for easy adjustments on the go, ensuring that the chain remains tight and secure during use. This design not only saves time but also enhances overall safety.

In conclusion, the Husqvarna 1153136-49 is a powerful, efficient, and user-friendly chainsaw packed with features that enhance performance and safety. It is an ideal choice for homeowners and anyone looking to manage their outdoor tasks effectively. With a strong engine, ergonomic design, and safety features, it represents a smart investment for maintaining gardens and outdoor spaces.
Top Page Image Contents