Ryobi RY34001 Operation, Attaching the Front Handle, Removing AN Attachment from the Power Head

Page 9

ASSEMBLY

NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place.

Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury.

ATTACHING THE FRONT HANDLE

See Figure 3.

Remove wing nut, washer, and bolt from the front handle.

Install the front handle onto the top side of the drive shaft housing in the area indicated by the label.

NOTE: The open side of the handle should face the operator. 

Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

Reinstall the washer and wing nut.

Tighten wing nut securely.

REMOVING AN ATTACHMENT FROM THE POWER HEAD

For removing or changing the attachment:

Stop the engine and disconnect the spark plug wire.

Loosen the knob.

Push in the button and twist the shafts to unlock and separate.

OPERATION

WARNING:

Do not allow familiarity with product to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing protection. Head protection may also be required depending on the type of attachment used and as prescribed in the attach- ment’s Operator’s Manual. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not recom- mended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

WARNING:

Gasoline and its vapors are highly flammable and ex- plosive. To prevent serious personal injury and property damage, handle it with care. Keep away from ignition sources and open flames, handle outdoors only, do not smoke and wipe up spills immediately.

FUELING AND REFUELING THE POWER HEAD

Clean surface around fuel cap to prevent contamination.

Loosen fuel cap slowly by turning counterclockwise. Rest the cap on a clean surface.

Carefully pour fuel into the tank. Avoid spillage.

Prior to replacing the fuel cap, clean and inspect the gasket.

Immediately replace fuel cap and hand tighten by turning it clockwise. Wipe up any fuel spillage.

Move at least 30 ft. away from refueling area before starting the product.

NOTE: It is normal for smoke to be emitted from a new engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle fuel could result in serious personal injury.

7 — English

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Toutes LES Versions Todas LAS Versiones Save this Manual for Future ReferencePage Iii Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules Specific Safety Rules for Trimmer USESpecific Safety Rules for ­BRUSHCUTTER and Blade USE Symbols Symbol Signal MeaningSymbol Name Explanation Assembly FeaturesFueling and Refueling the Power Head Removing AN Attachment from the Power HeadOperation Attaching the Front HandleDo not USE E85 FUEL. IT will Void Your Warranty Operating the Power HeadOxygenated Fuels ADDING/CHECKING Engine LubricantGeneral Maintenance MaintenanceBlade Thrust Starting and StoppingIdle Speed Adjustment Cleaning the Exhaust Port and Muffler Spark ArrestorCleaning AIR Filter Screen Spark Plug ReplacementWhen storing 1 month or longer Adjusting CAMSHAFT-TO-ROCKER ARM ClearanceStoring the Product High Altitude Engine OperationProblem Possible Cause Solution TroubleshootingIng Air Filter Screen earlier in this See Adding/Checking EngineLimited Warranty Statement WarrantyMANUFACTURER’S Warranty Coverage This Product WAS Manufactured with a Catalyst Muffler English Règles DE Sécurité Générales AvertissementLire Toutes LES Instructions Règles DE Sécurité Particulières Symbole NOM Explication SymbolesAssemblage CaractéristiquesRetrait DE L’ACCESSOIRE DU BLOC- Moteur Installation DE LA Poignée AvantRetrait ou remplacement de l’accessoire UtilisationCarburants Oxygénés AJOUT/VÉRIFICATION DE LubrifiantUtilisation DU BLOC-MOTEUR Ricochet DE Lame EntretienDémarrage ET Arrêt Avertissement AvertissementPARE-ÉTINCELLES Bouchon DU RéservoirRéglage DU Ralenti Changer LE Lubrifiant À MoteurFonctionnement DU Moteur À Haute Altitude Remisage LE ProduitVoir les figures 13 à Remisage 1 mois ou plusRemplacement de la bougie plus Problème Cause Possible SolutionDépannage Section Nettoyage du filtre à airÉnoncé DE LA Garantie Limitée GarantieResponsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Fonctionnement Chaque année ’AIDE?Reglas DE Seguridad Generales AdvertenciaLEA Todas LAS Instrucciones Reglas DE Seguridad Específicas Símbolos PeligroPrecaución Armado CaracterísticasMontaje DEL Mango Delantero FuncionamientoDesmontaje UN Aditamento DEL Cabezal Motor Para desmontar o cambiar el aditamentoAbastecimiento Y Verificación DE Lubricante Combustibles OxigenadosManejo DE EL Cabezal Motor No USE Combustible E85. Anulará SU GarantíaContragolpe DE LA Cuchilla MantenimientoArranque Y Apagado Mantenimiento GeneralParachispas Limpieza DEL Orificio DE Escape Y DEL SilenciadorAjuste DE LA Marcha Lenta Limpieza DEL Filtro DE Aire PantallaAlmacenamiento DE LA Producto Ajuste DE LA Apertura DEL Árbol DE Levas DEL BalancínOperación DEL Motor a Altitudes Elevadas Vea las figuras 13 aSolución DE Problemas Declaración DE LA Garantía Limitada GarantíaCobertura DE LA Garantía DEL Fabricante 4050 Este Producto SE Fabricó CON UN Silenciador CatalíticoEnglish California Proposition Manuel D’UTILISATION / Manual DEL OperadorProposition 65 DE L’ÉTAT DE Californie California Propuesta DE LEY NÚM

RY34001 specifications

The Ryobi RY34001 is a versatile outdoor power tool designed for homeowners and DIY enthusiasts seeking reliable performance in a handheld leaf blower. This battery-powered leaf blower offers a convenient way to maintain your yard, driveway, and patio, eliminating debris and leaves effortlessly.

One of the standout features of the RY34001 is its powerful 40V lithium-ion battery. This battery technology provides a significant advantage over traditional gas-powered blowers, delivering consistent and potent power without the hassle of gas or oil mixtures. Users can enjoy longer run times, enabling them to complete their yard work without interruptions. Additionally, the battery charge time is relatively quick, allowing users to get back to their tasks without long waits.

The RY34001 is designed with an impressive air volume rating of up to 540 CFM (cubic feet per minute) and an air speed of up to 130 MPH. This combination ensures that it can easily tackle heavy debris and wet leaves, making it perfect for both light clean-up tasks and more demanding jobs. The variable speed trigger allows users to adjust the airflow to suit their specific needs, whether they are moving light grass clippings or dealing with stubborn, wet piles of leaves.

Another notable characteristic of the Ryobi RY34001 is its ergonomic design. The blower features a lightweight construction, making it easy to handle and maneuver during operation. This design is complemented by a comfortable grip, reducing fatigue during extended use. The unit also includes a built-in cord retainer to prevent accidental disconnection, further enhancing user experience.

Ryobi has incorporated their patented technology into the RY34001, ensuring it delivers reliable performance time after time. The unit is also compatible with other Ryobi 40V tools, making it a valuable addition to a growing collection of outdoor equipment. With the RY34001, users can embrace a clean and well-maintained yard with the convenience of battery power, proving that efficiency and performance can go hand in hand. Whether you have a small garden or a larger property, the Ryobi RY34001 leaf blower is an excellent tool for simplifying yard maintenance.
Top Page Image Contents