Remington M12510US, M15012US, M15014US, M15014AS, M30016US, M30016AS, M30016AW, M35016UW, M35016AW

Page 16

CLEANING AND

MAINTENANCE

Continued

Items Needed to Sharpen Chain

Purchase these items from your local dealer, hard- ware store, or chain saw supplies outlet.

5/32" round file

Depth gauge tool

File guide

Vise

Medium sized flat file

Sharpening Cutters

Use file guide for 30° filing.

1.Adjust chain for proper tension (see Saw Chain Tension Adjustment, pages 8 and 9).

2.Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain.

3.Press 5/32" round file (attached to file guide) into groove between top plate and depth gauge on chain. File guide should rest on both top plate and depth gauge (see Figure 22). Note: File at midpoint of guide bar.

Filing Direction

30° Guide Mark

File Guide

5/32" Round

File

Note: This illustration shows file guide placement and filing direction for sharpening cutters on left side of chain.

Figure 22 - File and File Guide Placement On Chain

Depth Gauge (right

Depth Gauge (left side of chain) side of chain)

Groove

Groove

4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 22). This will insure that you file cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 22). Note: Two or three strokes with file should sharpen cutter.

6.After each cutter is sharpened, move chain for- ward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpen- ing, reset cutter depth gauges.

1.Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 24).

2.Use medium flat file. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 25).

After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see

Replacement Parts and Accessories, page 17.

Flat File

Depth

Gauge

Depth Gauge Tool

Depth Gauge Slot

Figure 24 - Depth Gauge Tool On Chain

Front Corner

.025"

.635 mm

Top Plate (left side of chain)

Top Plate

(right side of chain)

Right Side of Chain

Figure 25 - Round Off Front Corner Of Depth

Figure 23 - Chain Part Locations

Gauge

www.desatech.com

16

113005

Image 16
Contents Electric Chain SAW Contents Important Safety Information Before Operating SAWWhile Operating SAW Read ALL InstructionsKickback Safety Devices On This Saw KickbackMaintenance and Storage of Chain SAW A dry placeProduct Identification UnpackingChain SAW Names and Terms Indicator on side cover of saw AssemblyTop of guide bar face guide bar nose see Figure Bar, allow chain to cool then SAW Chain Tension AdjustmentLoosen nut Operating Chain SAW Turn chain tensioning screw Clockwise to tension saw chainFilling OIL Tank Oiling ChainClearing Sprocket Cover of Debris Extension CordsCutting with the Chain SAW Felling a Tree Cutting Down a TreeBefore Felling a Tree Practice until you can maintain a steady, even cutting rateFelling Procedure Felling Notch Felling CutLimbing a Tree Cut towards notchBucking a LOG Entire Length Of Log On GroundLog Supported On One End Log Supported On Both EndsCutting a Limb Cleaning Maintenance Cleaning SAW BodyNormal Guide Bar Maintenance Care of Guide BARItems Needed to Sharpen Chain Sharpening CuttersFiling Cutter Depth Gauges Replacing SAW ChainTechnical Service Replacement Parts and AccessoriesRepair Service StorageTroubleshooting Observed Fault Possible Cause RemedyElectric Chain SAW Limited Warranty Model Date PurchasedSierra Eléctrica Información Importante DE Seguridad Limpieza Y MantenimientoInformación Importante DE Seguridad Antes DE Utilizar LA SierraAL Utilizar LA Sierra LEA Todas LAS InstruccionesLleve la sierra eléctrica de un lugar a otro ContragolpesCon el dedo fuera del gatillo Mantenimiento Y Almacenamiento DE SU Sierra Eléctrica Identificación DEL Producto DesembalajeRetire todos los elementos del embalaje Terminología Rueda dentada Rueda dentada que impulsa la cadenaEnsamblaje Figura 5 Bloqueo del retenedor de la barra guíaAjuste DE Tensión DE LA Cadena Serrada ImportanteUSO DE LA Sierra Eléctrica LubricaciónLubricación DE LA Cadena Sistema de lubricación manual De 0C, utilice aceite lubricante SAE #10. Si laRemoción DE Restos DE LA Tapa DE LA Rueda Dentada Cables DE Prolongación15 m 30 mRealización DE Cortes Tala DE UN Árbol Derribamiento de un árbolAntes de derribar un árbol AdvertenciaProcedimiento de tala Corte de la muesca Tala finalCorte en dirección a la muesca Desmembramiento DE UN Árbol Trozado DE UN TroncoLa totalidad del tronco sobre el suelo Siga estas instrucciones para trozar un troncoTronco apoyado sobre ambos extremos Tronco apoyado en un extremoPoda DE UN Árbol Limpieza DEL Cabezal Limpieza Y MantenimientoCuidado DE LA Barra DE Guía Mantenimiento normal de la barra de guía Afilado DE LA CadenaElementos necesarios para afilar la cadena Afilado de los elementos de corteRecambio DE LA Cadena Serrada Limado de los calibradores de medida de profundidadDentada adecuada a su modelo, consulte la sección Almacenamiento Servicio TécnicoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónDiagnóstico Y Resolución DE Problemas Falla Observada Causa Posible SoluciónGarantía Limitada DE Sierra Eléctrica Modelo Fecha de compraTronçonneuse Électrique Prime Consignes DE Sécurité Importantes Nettoyage ET EntretienAgréé voir Service Técnique, Lorsquon est pressé Consignes DE Sécurité ImportantesAvant D’UTILISER LA Tronçonneuse Pendant Lutilisation DE LA TronçonneuseSuite ReculEntretien de la tronçonneuse et protection contre le recul Entretien ET Remisage DE LA TronçonneuseDéballage Identification DU ProduitVocabulaire DE LA Tronçonneuse Lisation sécuritaire et correcte de la tronçonneuseMontage Le tronçonnage et l’abattageBoulon et sur le dispositif de retenue du guide Voyant sur le capot latéral de la tronçonneuseAu besoin, resserrer à la main l’écrou du guide- chaîne ÉtapeRéglage DE LA Tension DE LA Chaîne Utilisation DE LA Tronçonneuse Remplissage DU Réservoir D’HUILELubrification DE LA Chaîne Système de lubrification manuel Nettoyage DES Débris DU Couvercle DU PignonLe crochet de maintien de la rallonge jusquà ce quil Rallonges ÉlectriquesCordon dalimentation de la tronçonneuse Sciage Avec LA Tronçonneuse Abattage D’UN ArbreAvant d’abattre un arbre AvertissementProcédure d’abattage Sifflet d’abattage Trait d’abattageEnlever le morceau de tronc créé par les deux entailles ’entaille inférieure Scier en direction du siffletÉbranchage Tronçonnage D’UNE BilleToute la bille repose au sol La bille est soutenue aux deux extrémitésLa bille est soutenue à une extrémité Taille D’UN Arbre ÉlagageNettoyage ET Entretien Nettoyage DU Carter DE TronçonneuseEntretien DE LA GUIDE-CHAÎNE Entretien normal de la guide-chaîneAffûtage DE LA Chaîne Outils nécessaires pour affûter la chaîneRemplacement DE LA Chaîne Affûtage des taillantsLimage des limiteurs de profondeur des taillants Utiliser le guide lime pour un limage à 30˚Service Technique Pièces DE Rechange ET AccessoiresService DE Réparation RemisageDépannage Défaillance Observée Cause Possible RemèdeInformation SUR LA Garantie Garantie Limitée Pour LA Tronçonneuse Électrique113005 Parts LIST/LISTA DE REPUESTOS/LISTE DES Pièces Renvoi Pièce DESCRIPTION/DESCRIPCIÓN/DESCRIPTIONContinúa/À suivre Parts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE Pièces 113005 113005 Stop