Athena Technologies 16C Output Types, A 120/240 Vac relay, but normally closed output 2 only

Page 9

Output Types

The Type “B” output is a mechanical device and subject to wear. To extend the life of the relay, set the Cycle Time for the relay output to the longest duration that still affords good control.

When you ordered your Series C controller specific output types were specified, designated as “B”, “E”, “F”, “G”, “S”, “T” or “Y”. You also had the option of configuring your con- troller with either one or two output actions. The numbers below are suggested for most typical applications.

For Control Output Type —

Select Cycle Time

 

(in seconds)

B

>15

E

0.2

F

0.2

G

0.2

S

0.2

T

15*

Y

>15

*“T” outputs directly driving non-inductive loads (small heaters) can have cycle times as low as 0.2 seconds.

Output Type

Description

B5 A (120/240 Vac) relay, normally open, used for switching resistive loads. If relays or sole- noids are to be driven, select the “T” output. If a “B” output is selected, order snubber network 235Z005U01.

E0-20 mA

F4-20 mA, full output to load with 500 ohm impedance max. (suppressed).

GHigh impedance ‘F’ (800 ohms).

S20 Vdc pulsed output for solid-state relays.

T1 A @ 120/240 Vac, solid-state relay, zero volt- age-switched and optically isolated from drive signal. Only resistive loads to 1A may be con- trolled directly. Larger loads may be controlled using an external contactor.

Y5 A (120/240 Vac) relay, but normally closed (output 2 only).

5

Image 9
Contents 16C Introduction Precautions FeaturesSafety Warning Contents Installation Mounting DimensionsContact Identification WiringRTDs. Connect 2-wire RTDs Make sure that you are using Appropriate thermocoupleWire, if necessary, to minimize Lead resistance. For long runs Wire RTDs should be usedA 120/240 Vac relay, but normally closed output 2 only Output TypesMode/Enter Key Menu Access KeyLower Key Raise KeySecurity Level, Menu System, and Operating Mode Power OnSecurity Levels Security Levels and Access RestrictionsManual Operating ModesMenu System Overview Been installed. Pressing the Menu Access key indexesMenu System Overview Menu SystemChart of Series 16C Menu System Security Levels On Next See options manual for parameter selections Descriptions Menus and ParameterDisplay Parameter Selection Input MenuJMPØ2 Display Menu Output MenuDisplay Parameter Output Menu Control Menu Output Type Recommended Setting secondsParameter Selection On/Off Output TypeSetpoint. High process alarm Below alarm settingDeviation Alarm Alarm Output Type Autotune Damping Menu Recipe Ramp/ Soak Menu Eter should be set to which will disable itPower Fail Resume Supervisor Menu Options Menu Calibration MenuTo place the controller in Autotune mode AutotuningAutotuning Procedure Diagram Band Manual TuningNumber is the correct Derivative Time SecondsError Codes Possible error codes areDisplay Problem Actions Technical Specifications Thermocouple Platinum 2- and 3-wire, 100 ohms atMaximum lead resistance 100 ohms For rated accuracyModel Input Calibration Type Ordering CodesRTD Calibration Values Quick-Helps Press and hold For 3 sec + PV + Two-Year Limited Warranty Warranty RepairsOther than those expressly stated herein, There are no BUYER’S Remedy is Limited to Either i Repair orUnit Repairs Requirements Fuse rating=100 mA250 Vpk 20 mA Glossary Applications for On/Off Control Quick Setup Instructions Series 16C Temperature Controller Configured Parameters Reference Data Page For Toll-FreeTechnical Assistance in the USA Call Toll Free

16C specifications

Athena Technologies is making waves in the aerospace and defense industries with its latest innovation, the Athena Technologies 16C. This advanced system is designed to provide detailed and accurate guidance, navigation, and control for unmanned aerial vehicles (UAVs) and other applications requiring precise positioning and situational awareness.

At the core of the Athena Technologies 16C is its state-of-the-art inertial navigation system. Utilizing a combination of accelerometers, gyroscopes, and advanced sensor fusion techniques, the 16C achieves exceptional accuracy even in challenging environments where GPS signals may be weak or nonexistent. This capability is crucial for military operations and search-and-rescue missions where precision is paramount.

One of the standout features of the 16C is its integrated multi-sensor environment, which includes not only traditional inertial sensors but also GPS, magnetometers, and barometric altimeters. This robust multi-sensor fusion system leverages cutting-edge algorithms to minimize errors, enhance reliability, and provide continuous position tracking regardless of external conditions. The flexibility of the sensor suite allows for easy integration into various platforms, whether fixed-wing, rotary-wing, or even ground-based vehicles.

Furthermore, Athena Technologies has prioritized ease of use with the 16C. The system comes equipped with intuitive software that simplifies mission planning and vehicle control. Users can easily adjust parameters, visualize data, and receive real-time feedback during operations, enhancing overall mission effectiveness. The user interface is designed to be user-friendly, catering to both experienced operators and newcomers to UAV technology.

Another notable characteristic of the Athena Technologies 16C is its rugged design, built to withstand harsh environmental conditions. This durability makes it suitable for deployment in diverse terrains and climates, ensuring reliable performance under even the most demanding situations. The system is lightweight yet robust, contributing to the overall efficiency and performance of unmanned systems.

Lastly, Athena Technologies emphasizes safety and security with the 16C. Advanced encryption methods safeguard the data transmitted between the system and ground control, ensuring that sensitive information remains protected from potential cyber threats. This commitment to security is crucial for military applications where data integrity is non-negotiable.

In conclusion, the Athena Technologies 16C stands out as a game-changing solution in the fields of guidance, navigation, and control. Its advanced multi-sensor capabilities, user-friendly interface, rugged design, and emphasis on security make it an essential tool for a wide range of applications, from military operations to commercial UAV usage. As technology continues to evolve, the 16C is poised to play a significant role in shaping the future of unmanned systems.