Craftsman MGP-769010 owner manual Tools Required for Assembly, Remove Pressure Washer from Carton

Page 6

Tools Required for Assembly

Adjustable wrench

Allen wrench

Remove Pressure Washer from Carton

•Open carton from the top. Locate and remove from box the handle, gun, wand, videotape, and oil.

•Cut carton along dotted lines.

•Remove all carton inserts.

•Roll unit through opening in carton.

NOTE: The hose is located at the bottom of the box.

Preparing the Pressure Washer for First Use

Note: Included with your pressure washer is a video cassette tape on how to prepare your unit for operation. It is recommended you view this tape before performing the next steps.

1. Insert handle onto frame.

•Insert knobs into the threaded slot in front of the frame handle and tighten by turning in a clock-wise direction.

•Slide bolts into the slot in the side of the frame handle and tighten the nuts by turning in a clock-wise direction.

Insert bolt and tighten

lock nut.

Tighten knob in

clockwise direction

2. Using an adjustable wrench, remove nut from bolt that attaches board to frame. Remove wood plank from the frame of the unit. Discard bolt and board.

3.Mount the rubber isolator to the frame. To

mount isolator place threaded end of bolt through the washer.

•Next with washer on bolt place threaded end of bolt through the larger hole in bottom of the rubber isolator.

•Place threaded portion of bolt through the same hole location the wood plank was mounted to on the pressure washer.

•Next place the tee nut over the threaded portion of the bolt and use the Allen wrench provided to tighten isolator to the frame.

TEE NUT

PRESSUREISOLATOR

WASHER

FRAME

WASHER

BOLT

4.Connect wand extension to gun. To tighten, turn knob in clockwise direction. Hand tighten.

5.Remove tie wrap off of high pressure hose. Unwind high pressure hose and attach the threaded end to the gun. Tighten with adjustable wrench.

6.Connect high pressure hose to outlet on pressure washer and hand tighten firmly. Connect chemical pickup hose to hose barb on pump.

				HIGH
				PRESSURE
				PRESSURE
CHEMICAL				HOSE
CHEMICAL				HOSE
HOSE

NOTE: Always keep hose away from engine muffler.

6

Image 6

Contents Operating Instructions Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ATable of Contents Result in death or serious injury Safety Guidelines DefinitionsImportant Safety Instructions DamageRisk of Unsafe Operation Assembly Carton ContentsTools Required for Assembly Remove Pressure Washer from CartonPreparing the Pressure Washer for First Use Checklist OperationKnow Your High Pressure Washer Engine Oil Stopping Your Pressure WasherBefore Starting The Engine GasolineTo Start Your Pressure Washer How To Use Your Pressure Washer Using Soaps/ChemicalsSplit Backup MaintenanceProduct Specifications General RecommendationsPurge Pump of Air and Contaminants Pressure Washer MaintenanceEngine Maintenance Check Oil Level Changing Engine OilClean and Replace Spark Plug Service and AdjustmentsClean Pre-Cleaner and Air Cleaner Cartridge Nozzle CleaningEngine Preparation StoragePreparing Pressure Washer for Storage Pump PreparationTroubleshooting Problem Cause CorrectionNo or low pressure after PARTS/PARTES 900Not Included with Pressure Washer Pump PARTS/BOMBA Partes Parts Kits Engine PARTS/MOTOR Partes Briggs Engine Model #120602-01350-E2Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Engine PARTS/MOTOR Partes Briggs & Stratton Emission Control Defects Warranty Coverage Owner’s Warranty ResponsibilitiesAbout your engine warranty Improper maintenanceNormal wear Tabla DE Contenidos Garantía Limitada DE DOS Años DEL Motor CraftsmanCausará la muerte o lesiones serias Pautas DE Seguridad DefinicionesInstrucciones Importantes DE Seguridad ModeradasRiesgo DE Operación Insegura Ensamblaje Riesgo DE Lesiones YPreparación de la Lavadora a Presión para el Primer Uso Herramientas Requeridas para el EnsamblajeSacar la Lavadora a Presión de la Caja Nota La manguera se encuentra en el fondo de la cajaFamiliarizarse con la Lavadora a Presión OperaciónLista de Comprobación Antes de continuar, por favor comprobar lo siguienteAceite del Motor Apagado de la Lavadora a PresiónAntes de Arrancar el Motor GasolinaPara Arrancar la Lavadora a Presión Como usar la Lavadora a Presión Uso de Detergentes y QuímicosPurgar el aire y los contaminantes de la bomba MantenimientoRecomendaciones Generales Aro reténPurgar el Aire y los Contaminantes De la Bomba Mantenimiento de la Lavadora a PresiónMantenimiento de la bomba Cambio del aceite de la bomba Mantenimiento del Motor Revisar el Nivel del AceiteCarburador Mantenimiento Y RegulacionesLimpiar y Reemplazar la Bujía Limpieza de la BoquillaPreparación del Motor AlmacenamientoPreparación de la unidad para su Almacenamiento Preparación de la BombaGuia DE Diagnosticos DE Problemas Nada o baja presión después Responsabilidades del propietario de la garantía Acerca de la garantía de su motor Desgaste normalNotas Notas Notas Get it fixed, at your home or ours