Zenoah RMSZ2601-CA Gearcase Lubrication, Replacing the Gearcase OIL MA1, End cap Main gear

Page 42

MA1

English

9.Maintenance

■GEARCASE LUBRICATION

With the exception of oil leaks or contamination, the RedMax Sweeper's oil filled gearcase is designed to last the life of the machine under normal use:

•It is not necessary to add oil or to "top off" the gearcase under normal operating conditions.

•For continuous heavy-duty applications, (such as where the machine will be stopped only during refueling), RedMax recommends replacing RedMax Sweeper gearcase oil every 40 hours of operation.

■REPLACING THE GEARCASE OIL (MA1)

Warm the gearcase oil by running the RedMax Sweeper at varying speeds for approximately 8-10 minutes, and then switch the engine to "OFF" and disconnect the spark plug wire at the engine. Use the following procedure to remove and replace all gearcase oil.

1.Remove the drum and axle assemblies (see page 19), and then remove the four end cap bolts and the end cap (the gearcase need not be removed from the RedMax Sweeper).

2.Allow all used gearcase oil to drain into a small container.

WARNING

BURN DANGER! The gearcase and oil will be extremely hot after use!

3.Place the RedMax Sweeper main gear flat. Refill the gearcase with Mobil SHC 634 Synthetic Gear Oil to the top of the main gear (60ml – 1.80zs), as shown. DO NOT OVERFILL! (MA1)

(1)End cap

(2)Main gear

4.Apply a continuous bead of loctite ultra grey around the pilot diameter of the end cap. Install the end cap, and then install and firmly tighten the four end cap bolts.

5.Install the drum and axle assemblies, and then reconnect the spark plug wire.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationRMSZ2601 / RMNBZ2601 / RMSZ2601-CA / RMNBZ2601-CA Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Wear head, eye and ear protection Symbols on the machineMachine PositionEmplacement PosiciónFor safe operation Working ConditionWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineUse only for tasks explained in the manual Utilisation DE LA Machine Demarrage DU MoteurArranque DEL Motor USO DEL ProductoMaintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulación DEL Combustible Manipulation DU CarburantTransport TransporteSweeper Assembly SE2 Set upInstall the Handle Clevis Pin Hitch Pin Cotter Pin Drum Axle Drum AssemblyAssemblage Montaje Ensemble DE Balayage SE2Conjunto DE LA Barredora SE2 Nylon Brush Attachment Procedure SE3Assemblage Montaje Set up Procédure d’installation Procedimiento de instalación When using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 OP3 OP4 Starting EngineSweeping head will start rotating upon the engine starts Fonctionnement Uso OP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 OP7 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Avant DE Commencer L’UTILISATIONOP8 OP9 Direction of rotationSens de rotation Técnicas DE Funcionamiento OP8 OP9 OP10Dirección de giro Maintain a shallow angle to the work surface Operating and Safety Tips OP11OP10 OP11 YOU Must Always Guard Against Thrown DebrisConsejos DE Funcionamiento Y Seguridad OP11 Fonctionnement UsoConseils D’UTILISATION ET DE Securite OP11 Vous Devez Toujours Vous Proteger DES Debris ProjetesAvoid low rpm operation General Safety InstructionsNever make unauthorized attachment installations Stay Alert Work SafelyInstructions Generales DE Securite Instrucciones Generales DE SeguridadMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoReplacing the Gearcase OIL MA1 MA1Gearcase Lubrication End cap Main gearEntretien Mantenimiento Remplacement DE L’HUILE DU Carter ’ENGRENAGE MA1Cambio DEL Aceite DE LA Caja DE Cambios MA1 Capot de carter Engrenage principalAIR Filter Replacement Plug is a NGK CMR7HMA2 MA3 MA4 Fuel FilterBougie D’ALLUMAGE Filtre a AIRFiltre a Carburant Filtro DE AireSpark Arrester Tightening TorqueMuffler MA5 MA6 Intake AIR Cooling VentSilencieux Silenciador Couple DE SerragePAR DE Torsión PARE-ETINCELLESDisposal Procedures to be Performed After Every 100 Hours of USEStorage MA7Mise au rebut Eliminación Procedure a Effectuer Toutes LES 100 Heures D’UTILISATIONRangement Almacenamiento Cilindro Toma de aire de refrigeración posteriorTroubleshooting guide 12. Guía de localización y solución de problemasGuide de localisation des pannes Barredora NotaRMSZ2601 / RMSZ2601-CA Pipe Comp RMNBZ2601 / RMNBZ2601-CA Nylon Brush Ass’y 99909-11004 Parts list Description Part Number Qty Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Control DE Emisiones Emission Control Mesures DE Lutte ContreLES Emissions RMSZ2601-CA/RMNBZ2601-CA RMSZ2601-CA/RMNBZ2601-CA

RMSZ2601-CA, RMNBZ2601-CA, RMNBZ2601, RMSZ2601 specifications

The Zenoah RMSZ2601, RMNBZ2601, RMNBZ2601-CA, and RMSZ2601-CA are advanced, high-performance engines designed for professional use in various applications, particularly in the realms of landscaping, agriculture, and industrial equipment. Known for their reliability and durability, these engines are engineered to meet the rigorous demands of both commercial and residential users.

One of the standout features of these models is their two-stroke engine design, which allows for a higher power-to-weight ratio compared to four-stroke engines. This lightweight construction makes the Zenoah engines easier to maneuver and operate in tight spaces without sacrificing power. The RMSZ2601, for instance, boasts a displacement of 26 cc, delivering impressive torque and efficiency, making it suitable for a range of tasks from trimming to industrial drives.

Another key characteristic of these engines is their advanced ignition system, which enhances starting ease and operational stability. The incorporation of Zenoah’s unique digital ignition technology ensures a quick start and consistent performance across varying conditions. Additionally, these engines are equipped with an anti-vibration system that minimizes operator fatigue, enabling extended use without discomfort.

The RMNBZ2601 and its variants are also designed with an emphasis on reduced emissions. The CA models incorporate catalytic converters to meet stringent environmental regulations, making them a responsible choice for users conscious of their ecological footprint. This not only helps comply with governmental standards but also contributes to a cleaner working environment.

Moreover, Zenoah emphasizes user-friendly features in their engine designs. Both the RMSZ2601 and RMNBZ2601 models feature easy-access fuel and oil tanks that simplify refueling and maintenance. The filters are conveniently positioned for straightforward cleaning and replacement, ensuring longer operational life and reliability.

Durability is a hallmark of the Zenoah brand. The engines are constructed with high-grade materials that withstand the rigors of heavy-duty use. This ensures that the RMSZ2601, RMNBZ2601, and their variants maintain peak performance over time, even under challenging operating conditions.

In summary, the Zenoah RMSZ2601, RMNBZ2601, RMNBZ2601-CA, and RMSZ2601-CA represent cutting-edge technology in the small engine market, delivering robust performance, low emissions, and reliability. These features make them ideal choices for professionals in landscaping, agriculture, and other demanding sectors.
Top Page Image Contents