Generac 005031-2 owner manual Exploded Views and Parts Lists, Liquid-cooled25 kW Generators

Contents SHOULD ATTEMPT INSTALLATION Liquid-cooled,Prepackaged Standby GeneratorsModel Number 005031-225kW This manual should remain with the unitAUTHORIZED SERVICE DEALER LOCATION ‹OPERATION AND MAINTENANCE‹HOW TO OBTAIN SERVICE INTRODUCTIONINTRODUCTION ELECTRICAL HAZARDS  GENERAL HAZARDSWARNING   EXPLOSION HAZARDS FIRE HAZARDS‹STANDARDS INDEX 1.2TRANSFER SWITCH 1.1GENERATOR1.3ATS MODE AUTOMATIC OPERATION 1.4GENERATOR AC CONNECTION SYSTEMS‹1.7.1 LOW OIL PRESSURE SWITCH ‹1.7.2 HIGH COOLANT TEMPERATURE SWITCH‹1.7.3 LOW COOLANT LEVEL SWITCH Figure 1.4 - Low Oil Pressure Switch1.10 SPECIFICATIONS ‹1.7.6 LOW BATTERY‹1.8.1 UNPACKING PRECAUTIONS 1.8UNPACKING1.12RECONFIGURING THE FUEL SYSTEM FOR LP VAPOR Figure 1.8 - Reconfigure the Fuel System1.11 FUEL CONSUMPTION 1.13 ENGINE OIL RECOMMENDATIONS2.1STANDBY GENERATOR INSTALLATION 1.15 BEFORE INSTALLATION1.14 COOLANT RECOMMENDATIONS ‹2.1.1 NFPA STANDARDS2.2GENERATOR LOCATION 2.3GENERATOR MOUNTING AND SUPPORT2.4BASIC STANDBY ELECTRIC SYSTEM ‹2.1.2 OTHER PUBLISHED STANDARDS2.9USING A “GTS” TRANSFER SWITCH 2.5EMERGENCY CIRCUIT ISOLATION METHOD2.6TOTAL CIRCUIT ISOLATION METHOD 2.7GROUNDING THE GENERATORPos2 OFF — ATS Application 2.10 BATTERY INSTALLATION‹2.10.1 VENTED BATTERIES 3.1GTS TRANSFER SWITCH ‹2.11.2 TRANSFER SWITCH2.11 PREPARATION BEFORE START-UP ‹2.11.4 GENERATOR SET LUBRICATION‹3.2.1 AUTO/OFF/MANUAL SWITCH ‹3.2.2 FAULT INDICATOR LEDS3.2CONTROL CONSOLE COMPONENTS GTS Mode Operation‹3.2.5 SET EXERCISE TIME SWITCH ‹3.2.3 15 AMP FUSE‹3.2.4 5 AMP FUSE ‹3.2.6 SYSTEM READY LED3.4ENGINE GOVERNOR GAIN ADJUSTMENTS 3.3MANUAL TRANSFER AND START-UP3.5MANUAL RETRANSFER AND SHUTDOWN Figure 3.2 - Engine Governor Adjustment3.8CONTROL BOARD DIP SWITCH SETTINGS Figure 3.3 - “Set Exercise Time” Switch3.6AUTOMATIC OPERATION 3.7WEEKLY EXERCISE CYCLE3.9VOLTAGE REGULATOR ADJUSTMENT ‹EVERY THREE MONTHS‹ONCE EVERY SIX MONTHS ‹ONCE ANNUALLY4.2EXHAUST MANIFOLD PROCEDURE 4.3INTAKE MANIFOLD PROCEDURE4.4CYLINDER HEAD PROCEDURE Figure 4.1 - Intake Manifold Installation4.8MAINTENANCE OWNER/ OPERATOR CAN PERFORM ‹4.7.2 BATTERY FLUID‹4.8.2 CHECK BATTERY 4.6OVERLOAD PROTECTION FOR‹4.8.11 CHANGING THE ENGINE AIR CLEANER Figure 4.4 - Setting the Spark Plug Gap‹4.8.7 INSPECT EXHAUST SYSTEM ‹4.8.8 CHECK FAN BELT4.9MISCELLANEOUS MAINTENANCE ‹4.9.1 CLEANING THE GENERATOR‹4.9.2 BATTERY ‹4.9.3 BATTERY MAINTENANCE4.10 SCHEDULED MAINTENANCE Service Maintenance Interval InformationTasks Level TROUBLESHOOTING POINTS PROBLEMCAUSE CORRECTIONSection 6 - Electrical Data Section 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW GeneratorsSection 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW GeneratorsSection 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW GeneratorsSection 6 - Electrical Data Section 7 - Exploded Views and Parts Lists DESCRIPTION Mounting Base - Drawing No. 0F0104-B38 3 45 39 32 18 LATCH DETAIL Enclosure - Drawing No. 0F1645-H Section 7 - Exploded Views and Parts Lists 0F0790 Control Panel 25kW - Drawing No. 0E7615-C Section 7 - Exploded Views and Parts Lists FOR HARNESS GROUND STEPPERONLY RADIATOREngine - Drawing No. 0E9918-F COVER Fuel System - Drawing No. 0E9980-D LOCKTIGHT LEADS0F1659A Muffler - Drawing No. 0F2930-C Stepper Motor - Drawing No. 0E9979-C TO THERMOSTAT Radiator - Drawing No. 0E9965-FADAPTER Section 8 - Installation Diagram PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES YOUR WARRANTY RIGHTS AND OBLIGATIONSCALIFORNIA EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL SYSTEM WARRANTY EMISSION RELATED PARTS INCLUDE THE FOLLOWINGWARRANTY SCHEDULE THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING