Generac 004626-1, 004373-2, 004373-2, 004626-1 owner manual 12V Battery see Note Lifting EYE Places

Page 59

Section 9 — Installation Drawings

Guardian Liquid-cooled 40 kW Generators Installation Drawing – Drawing No. 0D5335

RECOMMENDED FUEL/ELECTRICAL STUB-UPS (SEE TOP VIEW)

DESCRIPTION		INSIDE
DESCRIPTION		BASE
		BASE
AC LOAD LEAD CONDUIT	(LEFT)		A1
INSIDE STUB-UP FOR
INSIDE STUB-UP FOR			C
FUEL CONNECTIONS			C

NOTE:

FUEL SYSTEM SET UP WITH OUTSIDE STUB UPS (SEE LEFT SIDE VIEW). SMALL FUEL SYSTEM MODIFICATIONS REQUIRED FOR

INSIDE STUB-UPS.

WEIGHT DATA

UNIT: 729.7 kg [1609 lbs]

STEEL COMPARTMENT: 208.6 kg [460 lbs]

UNITS: mm [INCHES]

965 [37.99"]

1160 [45.67"]

877 [34.51"]

REAR VIEW

NOTES:

1.STANDARD BLOCK HEATER REQUIRES 120V AC CONNECTION

2.CONNECTION POINTS FOR AC LOAD LEADS, TRANSFER SWITCH, AND

ENGINE AUTOMATIC START/STOP CONTROL WIRES PROVIDED IN

AC CONNECTION PANEL.

3.EXHAUST MUFFLER SUPPORT BRACKETS SUPPLIED WITH OPTIONAL COMPARTMENT.

4.12 VOLT NEGATIVE GROUND SYSTEM

BATTERY TRAY INSIDE DIMENSIONS: 178 X 342.5 [7" X 13.5"]

5.2.5" I.D. FLEX EXHAUST

6.MAIN LINE CIRCUIT BREAKER.

7.DOORS MUST BE OPENED 90 DEG. TO BE REMOVED.

8. A1 MAY BE USED

FOR CIRCUIT BREAKER STUB-UP LOCATION.

9.SEE DRAWING C3850 FOR DUCT REMOVAL. REMOVAL OF FRONT DUCT WILL PROVIDE ACCESS TO MUFFLER FOR SERVICING.

ENGINE SERVICE CONNECTIONS

INLET NATURAL GAS = 3/4" NPT COUPLING

OIL DRAIN = 1/2" NPT COUPLING

EXHAUST OUTLET -

2.5" OD MUFFLER OUTLET

(1) 12V BATTERY SEE NOTE 4

LIFTING EYE

(4 PLACES)

158 [6.22"]

CENTER OF

GRAVITY

981 [38.62"]

1930 [75.98"]

RIGHT SIDE VIEW

Generac® Power Systems, Inc. 57

Image 59

Contents Power SYSTEMS, INC Authorized Dealer Location IntroductionSection Installation Drawings 56-57 Warranty Back Cover Safety Rules General InformationInstallation MaintenanceGeneral Hazards Electrical Hazards Generator AC Connection Systems Prepackaged Transfer SwitchUNPACKING/INSPECTION GeneratorEngine Protective Devices SpecificationsMain Circuit Breaker Conversion to LP GAS Vapor Fuel Requirements RecommendationsGenerator and Load Compatibility EngineAIR Fuel Ratio Controller CoolantEmissions Control System Other Published Standards Standby Generator InstallationBasic Standby Electric System Nfpa StandardsEmergency Circuit Isolation Method Transfer Switch Start Signal ConnectionsPre-Packaged Type Switch GTS Type Engineered SwitchVented Batteries Battery InstallationPreparation Before START-UP Prior to Initial START-UP Using the AUTO/OFF/MANUAL Switch Sequence of Automatic Operation OFF PositionManual Position Automatic Transfer OperationChecking the Engine OIL Level Weekly Exercise CycleEngine Oil Recommendations Oil and Filter Change ProcedureChanging the Engine AIR Cleaner Changing the Engine OIL and FilterSpark Plugs Battery MaintenanceDC Fuse Miscellaneous MaintenanceCleaning the Generator Overload Protection for Engine DC Electrical SystemReturn To Service OUT of Service ProcedureRemoval From Service SYSTEM/COMPONENT Procedure Frequency Service ScheduleProblem Cause Correction Troubleshooting GuideElectrical Data Section Generac Generac Power Systems,Inc Electrical Data Electrical Data Electrical Data Wiring Diagram Customer Connection HRS Power Systems IncPart NO. QTY. Description Generators Part NO. QTY Description Part NO.QTY Description QTY Description 4640 31 33 Washer Flat 3/8-M10 Zinc Part NO.QTY. DescriptionExploded Views and Parts Lists Flywhl 4.3L GM SAE Stator Leads Scrolldetail To Engine Flywheel QTY Description Part NO. QTY Description QTY Assembly Cover AccessRadiator Copper Brass Gasket Carburetor Adaptor Gasket Carb Impco To Carburetor QTY. DescriptionSupport Solenoid NAT GAS QTY. Description To Starter Solenoid RED Black To Engine Block ALT Leads Sensing Wire Siemens FD 3 Pole QTY Description Exploded Views and Parts Lists Part NO. QTY. Description Muffler 2-1/2 INLET/OUTLET Guardian Liquid-cooled 40 kW Generators Installation Drawings 12V Battery see Note Lifting EYE Places This Warranty Shall not Apply to the Following Warranty Schedule