Craftsman 247.88664 owner manual Training, Preparation

Page 3

_lb

WARNING:

This symbol points out important safety instructions which, if not followed,

could endanger

 

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

 

before attempting to operate this machine. Failure to comply with these instructions may result in personal

 

injury. When you see this symbol--heed its warning.

 

,_

WARNING:

Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit

 

chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

Training

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their operation. Know how to stop the machine and disengage controls.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.

2.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

3.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

4.Use a grounded three-wire extension cord and receptacle for all units with electric start engines.

5.Adjust collector housing height to clear gravel or crushed rock surfaces.

6.Disengage all clutch levers before starting the engine.

7.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator's manual.

8.Let engine and machine adjust to outdoor temperature before starting to clear snow.

9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refueling.

f.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).

j.Allow unit to cool for 5 minutes before storing.

Operation

1.Do not put hands or feet near rotating parts, in the auger/ impeller housing or discharge chute. Contact with the rotating parts can amputate hands and feet.

2.The auger/impeller clutch lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury.

3.The clutch levers must operate easily in both directions and automatically return to the disengaged position when released.

4.Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.

5.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

6.Do not operate machine while under the influence of alcohol or drugs.

Image 3
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A Horse Power Two-StageSafety Model NoContent Two -Year Warranty on Craftsman Snow ThrowerPreparation TrainingSnowattoofastofarate Your ResponsibilityNottouch OrallowanyoneinfrontofthemachineShear bolts and lock nuts Setting Up The Snow ThrowerUnpacking Hardware PackTraction Control & Shift Lever Final Assembly & AdjustmentsChute Clean-Out Tool Auger ControlTire Pressure To Stop Engine Operating ControlsTo Start Engine Before StartingOperating Tips To Engage AugersBefore Stopping To Engage DriveSchedule Maintenance TasksGeneral Recommendations LubricationChecking Oil Level Engine MaintenanceEngine Oil Spark PlugTire Pressure Check V-BeltsCheck Friction Wheel Shave Plate and Skid Shoes Toacompletestop.Disconnectsparkplug wireReplacing Belts Servicing AugersFriction Wheel Rubber Drive BeltFriction Wheel Rubber Plates Drive Wheels Making AdjustmentsTo adjust the auger clutch, refer to Final Assembly Skid ShoeIfthesnowthrowerwiltnotbeusedfor30daysor Trouble Possible Causes Corrective Action California & U.S. EPA Emission Control Warranty StatementOwners Warranty Responsibilities Manufacturers Emission Control System WarrantyImportant Note Emission Control System Warranty36\ Description Craftsman 5.0 HP Snow Thrower Model Key No. Part No 2421 313335 Roll Pin 370B 3olWasher Key No. Part No DescriptionIntake Valve Std, IncL OS IncL364 Key No. Pad Description351 355Rewind Starter Description Rewind StarterElectric Starter 33290E Motor Mode o de motor Craftsman ContenidoEsta garantia no cubre ADVERTENClA CapacitacibnPreparativos OperacibnMantenimiento & Almacenamiento QuemaduraNolostoqueMaterialesolesionesproducidasporlosrebotes Cortelacorrientealabarrena/ motor cuando transporte laConfiguracibn de la mbquina quitanieve DesempaquePaquete de hardware Control de la barrena Control de traccibn & palanca de cambiosEnsamblado & Ajustes Finales Herramienta de limpieza del canalPresibn de los neumbticos Controles de operacibn Para encender el motor Antes de encenderProcedimiento para engranar las barrenas Antes de detener la mdquinaPara detener el motor Procedimiento para engranar la transmisibnFechas de los Recomendaciones generalesLubricacibn Calendario de mantenimiento Tareas de mantBujia de encendido Palanca decambiosMantenimiento del motor Aceite del motorServicio de la barrena Presibn de los neum ticosCompruebe las correas en Compruebe la rueda de friccibnGoma de la rueda de friccibn Correas de las barrenasCorrea de transmisibn Realizacibn de ajustes Ensamblado del canalZapata antideslizante Ruedas de transmisibn Transmision de una ruedaTransmision en ambas ruedas Solucibn ProblemaCausaNota importante Garantia del sistema de control de emisionesPage MY-HOME Our HomeCanada Date Received Date Published Pages Total Models Paper doc # NotesProd Type DocType Doc Class Code