Craftsman 247.88664 General Recommendations, Lubrication, Maintenance Tasks, Schedule, Product

Page 11

General	Recommendations			Periodically check all fasteners and make sure
Always observe safety rules when performing any				these are tight.
Always observe safety rules when performing any
maintenance.
The warranty on this snow thrower does not cover			_	WARNING:		Before lubricating, repairing, or
items that	have been subjected to operator	abuse		inspecting, disengage all clutch levers and stop
items that	have been subjected to operator	abuse		engine. Wait		until all moving parts have come
or negligence. To receive full value from the				to a complete		stop. Disconnect	spark plug wire
warranty,	operator must maintain the snow	thrower		and ground	it against the engine		to prevent
as instructed in this manual.				unintended	starting.
Follow the maintenance schedule given below.

Maintenance

Maint.		Tasks	Before	Aftereach	&fterfirst2
			_=achuse	use	hours
					operation
Product:
Lubricate pivotpoints				I	I
Clean	equipment			,/
				,/
Clean	skid shoe			,/
				,/
Check	V belts
Engine:
Check	engine oil
Change		engine oil			_
Check	spark plug I		I	I	I

Empty fuel system

Lubrication

Wheels: Oil or spray lubricant into bearings at wheels at least once a season. Pull ktick pin, remove wheels, clean and coat axles with a multipurpose automotive grease. See Figure 7.

Oil	bearings
Klick Pin	, lubricant

Figure 7

Schedule

Every25 Every50 Before Service Dates

hours hours storage operation operation

,,,

II_ I

,/

iiiiiiiiiii

,/

Gear Shaft: Lubricate the gear shaft with a good all-weather multi-purpose light grease at least once a season or after every 25 hours of operation. Keep all grease and oil off the friction wheel and drive plate.

IMPORTANT: When lubricating engine or draining oil, avoid spillage onto transmission parts.

Gear Case: The worm gear case has been filled with grease at the factory. If disassembled for any reason, lubricate with 2 ounces of shell grease.

IMPORTANT: Do not overfill the gear case. Damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

Drive and Shifting Mechanism: Remove rear cover. Oil any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. See Figure 8. Use engine oil or a spray

11

Image 11

Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A Horse Power Two-StageSafety Model NoContent Two -Year Warranty on Craftsman Snow ThrowerPreparation TrainingSnowattoofastofarate Your ResponsibilityNottouch OrallowanyoneinfrontofthemachineShear bolts and lock nuts Setting Up The Snow ThrowerUnpacking Hardware PackTraction Control & Shift Lever Final Assembly & AdjustmentsChute Clean-Out Tool Auger ControlTire Pressure To Stop Engine Operating ControlsTo Start Engine Before StartingOperating Tips To Engage AugersBefore Stopping To Engage DriveSchedule Maintenance TasksGeneral Recommendations LubricationChecking Oil Level Engine MaintenanceEngine Oil Spark PlugCheck Friction Wheel Tire PressureCheck V-Belts Shave Plate and Skid Shoes Toacompletestop.Disconnectsparkplug wireReplacing Belts Servicing AugersFriction Wheel Rubber Plates Friction Wheel RubberDrive Belt Drive Wheels Making AdjustmentsTo adjust the auger clutch, refer to Final Assembly Skid ShoeIfthesnowthrowerwiltnotbeusedfor30daysor Trouble Possible Causes Corrective Action California & U.S. EPA Emission Control Warranty StatementOwners Warranty Responsibilities Manufacturers Emission Control System WarrantyImportant Note Emission Control System Warranty36\ Description Craftsman 5.0 HP Snow Thrower Model Key No. Part No 2421 313335 Roll Pin 370B 3olWasher Key No. Part No DescriptionIntake Valve Std, IncL OS IncL364 Key No. Pad Description351 355Electric Starter 33290E Rewind Starter DescriptionRewind Starter Esta garantia no cubre Motor Mode o de motor CraftsmanContenido ADVERTENClA CapacitacibnPreparativos OperacibnMantenimiento & Almacenamiento QuemaduraNolostoqueMaterialesolesionesproducidasporlosrebotes Cortelacorrientealabarrena/ motor cuando transporte laPaquete de hardware Configuracibn de la mbquina quitanieveDesempaque Control de la barrena Control de traccibn & palanca de cambiosEnsamblado & Ajustes Finales Herramienta de limpieza del canalPresibn de los neumbticos Controles de operacibn Para encender el motor Antes de encenderProcedimiento para engranar las barrenas Antes de detener la mdquinaPara detener el motor Procedimiento para engranar la transmisibnFechas de los Recomendaciones generalesLubricacibn Calendario de mantenimiento Tareas de mantBujia de encendido Palanca decambiosMantenimiento del motor Aceite del motorServicio de la barrena Presibn de los neum ticosCompruebe las correas en Compruebe la rueda de friccibnCorrea de transmisibn Goma de la rueda de friccibnCorreas de las barrenas Zapata antideslizante Realizacibn de ajustesEnsamblado del canal Transmision en ambas ruedas Ruedas de transmisibnTransmision de una rueda Solucibn ProblemaCausaNota importante Garantia del sistema de control de emisionesPage Canada MY-HOMEOur Home Date Received Date Published Pages Total Models Paper doc # NotesProd Type DocType Doc Class Code