Intel 5000 manual Curing Process, Applying the Adhesive on the Thermocouple Bead

Page 23

Thermal Metrology

Figure 5-9. Applying the Adhesive on the Thermocouple Bead

5.1.6Curing Process

1.Let the thermocouple attach sit in the open air for at least half an hour. Using any curing accelerator like Loctite 7452 Accelerator* for this step is not recommended. Rapid contraction of the adhesive during curing may weaken bead attach on the IHS.

2.Reconfirm electrical connectivity with DMM before removing the micromanipulator (Figure 5-8) (see Section 5.1.4, “Thermocouple Conditioning and Preparation” on page 19 step 2).

3.Remove the 3D Arm needle by holding down the MCH unit and lifting the arm.

4.Remove the Kapton tape, straighten the wire in the groove so it is flat all the way to the end of the groove (Figure 5-11).

5.Using a blade, shave excess adhesive above the IHS surface (Figure 5-11).

Note:

Take usual precautions when using open blades.

6.Install new Kapton tape to hold the thermocouple wire down and fill the rest of groove with adhesive (See Figure 5-12). Make sure the wire and insulation is entirely within the groove and below the IHS surface.

7.Curing time for the rest of the adhesive in the groove can be reduced using Loctite 7452 Accelerator.

8.Repeat step 5 to remove any access adhesive to ensure flat IHS for proper mechanical contact to the heatsink surface.

Intel® 631xESB/632xESB I/O Controller Hub Thermal Mechanical Design Guide

23

Image 23

Contents Thermal/Mechanical Design Guide Intel 5000 Series Chipset Memory Controller HubMCHPage Contents Figures Tables Revision Description Date Number Revision TableDesign Flow IntroductionThermal Design Process Definition of TermsTDP Reference DocumentsIntroduction Packaging Technology MCH Package Dimensions Top ViewPackage Mechanical Requirements MCH Package Dimensions Bottom ViewIntel 5000P Chipset MCH Thermal Specifications Thermal SpecificationsThermal Design Power TDP Case TemperatureIntel 5000X Chipset MCH Thermal Specifications Thermal Simulation Thermal Simulation Thermocouple Attach Support Equipment Sheet 1 MCH Case Temperature MeasurementThermal Metrology Supporting Test EquipmentDescription Part Number Calibration and Control Thermal Calibration and ControlsIHS Groove Thermocouple Attach Support Equipment Sheet 2Thermocouple Conditioning and Preparation IHS Groove DimensionsBending the Tip of the Thermocouple Thermocouple Attachment to the IHSThermocouple Bead Placement Position Bead on the Groove Step Applying the Adhesive on the Thermocouple Bead Curing Process11. Removing Excess Adhesive from the IHS 10. Thermocouple Wire Management GroovePower Simulation Software Thermal Metrology Heatsink Performance Reference Thermal SolutionOperating Environment Mechanical Design Envelope Board-Level Components Keepout DimensionsTall Torsional Clip Heatsink Board Component Keepout Tall Torsional Clip Heatsink Thermal Solution AssemblyRetention Mechanism Component Keepout Zones Heatsink OrientationHeatsink Clip Extruded Heatsink ProfilesMechanical Interface Material Thermal Interface MaterialTest Requirement Pass/Fail Criteria Reliability GuidelinesClip Retention Anchors Reliability Guidelines Sheet 1Reliability Guidelines Sheet 2 Reference Thermal Solution Reference Thermal Solution Motherboard Short Torsional Clip Heatsink Board Component Keepout Short Torsional Clip Heatsink Thermal Solution AssemblyShort Torsional Clip Heatsink Assembly Heatsink Clip Reference Thermal Solution Part Intel Part Number Supplier Contact Information Tall Torsional Clip Heatsink Thermal SolutionShort Torsional Clip Heatsink Thermal Solution Drawing Name Table B-1. Mechanical Drawing ListFigure B-1. Tall Torsional Clip Heatsink Assembly Drawing Figure B-2. Tall Torsional Clip Heatsink Drawing Sheet 1 Figure B-3. Tall Torsional Clip Heatsink Drawing Sheet 2 Figure B-4. Tall Torsional Clip Heatsink Clip Drawing Figure B-5. Short Torsional Clip Heatsink Assembly Drawing Figure B-6. Short Torsional Clip Heatsink DrawingSheet 1 Figure B-7. Short Torsional Clip Heatsink DrawingSheet 2 Figure B-8. Short Torsional Clip Heatsink Clip Drawing Mechanical Drawings