Eiki EIP-1000T Overloading, Object and Liquid Entry, Servicing, Damage Requiring Service, Heat

Page 10

15.Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16.Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17.Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18.Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e.If the product has been dropped or damaged in any way.

f.When the product exhibits a distinct change in performance, this indicates a need for service.

19.Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20.Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21.Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22.Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

DLP\ (Digital Light Processing) and DMD\ (Digital Micromirror Device) are trademarks of Texas Instruments, Inc.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries.

PC/AT is a registered trademark of International Business Machines Corporation in the United States.

Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

All other company or product names are trademarks or registered trademarks of their respective companies.

Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

7

Image 10
Contents EIP-1000T This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage Introduction A. onlyEiki INTERNATIONAL, INC Eiki PROJECTOR, Model EIP-1000TEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Using the Menu Screen For Future ReferenceContents Maintenance Maintenance Indicators Regarding the Lamp ReferencePower Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment QCNWGA075WJPZ AccessoriesOptional accessory QACCDA007WJPZLever 28, 48 Lamp indicator Focus ring For adjusting the focusHeight 31 Adjust Part Names and FunctionPart Names and Functions Rear adjustment FootExhaust vent Speaker Kensington Security Standard connector Rear ViewPicture Mode BAR, Cinema ZoomInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Quick Start Setup and ProjectionSTANDBY-ON On the remote control Upper sideStandard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection PRJ Mode Example Stretch Mode Picture SizeWhen using a wide screen 169 and projecting 169 image Screen Size and Projection DistanceWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection To audio output Connecting to Video EquipmentSub adaptor Connecting to Video Equipment To audio output terminal To RGB output terminal Computer Connecting to a ComputerTo INPUT1 terminal To Audio Terminal RGB Cable Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Turning the Projector On/Off Connecting the Power CordLamp indicator Power indicator STANDBY-ON button On button Turning the Projector onJector or eSTANDBY on the re Projector into standby modePress oSTANDBY-ON on the pro Mote control, then press that butAdjusting the Screen Size Switching the Input ModeAdjusting the Projected Image Adjusting the Focus Image ProjectionAdjust lever Make small adjustments Rear adjustment foot Adjusting the HeightUse the rear adjustment foot to make the projector level HeightAV Mute button Volume buttons Adjusting the VolumeScreen and turn off the sound Correcting Trapezoidal Distortion Press g Keystone to enter Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press g KeystoneResize Mode Press HresizeComputer Auto Sync Auto Sync Adjustment Operating with the Remote ControlSelecting the Picture Mode Freezing a Moving ImageComponent/INPUT 3/INPUT Menu ItemsInput 1 Component/INPUT Input 1 RGB/INPUT2 RGBItems you can set with Help menu Help menu nPress Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Press BmenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 3 mode2Adjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ menu ImageAdjusting the Projector Function PRJ ADJ menu 3Auto Power Off Function This function changes the fan rotation speedUtilizing Help menu functions Troubleshooting with Help menuPress Oor Qto select Help, then Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorRed on Internal Blocked air intake Relocate the projector to Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments GNDComputer Compatibility Chart SVGA, XGA, SXGA, SXGA+Troubleshooting 23-27An input signal type Picture is pink no green Specifications Product type Projector Model EIP-1000T Video systemDimensions Side BAR IndexStretch Index Deutschland & Österreich CanadaEastern Europe Japan & Worldwide