Eiki EIP-1000T owner manual Regarding the Lamp, Replacing the Lamp

Page 53

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (see page 45)

Purchase a replacement lamp of type AH-11201 from your place of purchase, nearest EIKI Authorized Dealer or Service Center.

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or Service Center to assure safe operation.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized Dealer or Service Center for repair.

50

Image 53
Contents EIP-1000T If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Eiki PROJECTOR, Model EIP-1000TEiki INTERNATIONAL, INC For Future Reference Using the Menu ScreenContents Reference Maintenance Maintenance Indicators Regarding the LampAccessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function Optional accessory AccessoriesQCNWGA075WJPZ QACCDA007WJPZHeight 31 Adjust Focus ring For adjusting the focusLever 28, 48 Lamp indicator Part Names and FunctionExhaust vent Speaker Kensington Security Standard connector Rear adjustment FootPart Names and Functions Rear ViewBAR, Cinema Zoom Picture ModeAttach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range STANDBY-ON Setup and ProjectionQuick Start Upper side On the remote controlSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample Stretch Mode Picture Size Projection PRJ ModeScreen Size and Projection Distance When using a wide screen 169 and projecting 169 imageWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection Sub adaptor Connecting to Video EquipmentTo audio output Connecting to Video Equipment To INPUT1 terminal To Audio Terminal RGB Cable Connecting to a ComputerTo audio output terminal To RGB output terminal Computer Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Lamp indicator Power indicator STANDBY-ON button On button Connecting the Power CordTurning the Projector On/Off Turning the Projector onPress oSTANDBY-ON on the pro Projector into standby modeJector or eSTANDBY on the re Mote control, then press that butAdjusting the Projected Image Adjusting the Focus Switching the Input ModeAdjusting the Screen Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjust lever Make small adjustments Rear adjustment foot HeightScreen and turn off the sound Adjusting the VolumeAV Mute button Volume buttons Press P/Q or O/R to adjust Keystone Correction Press g Keystone to enter Keystone Correction modeCorrecting Trapezoidal Distortion Press g KeystonePress Hresize Resize ModeComputer Selecting the Picture Mode Operating with the Remote ControlAuto Sync Auto Sync Adjustment Freezing a Moving ImageInput 1 Component/INPUT Menu ItemsComponent/INPUT 3/INPUT Input 1 RGB/INPUT2 RGBHelp menu n Items you can set with Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press BmenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press hENTERExample Picture screen menu for Input 3 mode Picture Adjustment Picture menuMenu operation n 2Adjusting the ImageImage Adjusting the Projected Image SCR ADJ menuAdjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speed 3Auto Power Off FunctionPress Oor Qto select Help, then Troubleshooting with Help menuUtilizing Help menu functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsRed on Internal Blocked air intake Relocate the projector to Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer GND Connecting Pin AssignmentsSVGA, XGA, SXGA, SXGA+ Computer Compatibility Chart23-27 TroubleshootingAn input signal type Picture is pink no green Product type Projector Model EIP-1000T Video system SpecificationsDimensions Stretch IndexSide BAR Index Eastern Europe CanadaDeutschland & Österreich Japan & Worldwide