Eiki owner manual Eiki PROJECTOR, Model EIP-1000T, Eiki INTERNATIONAL, INC

Page 5
U.S.A. ONLY

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY-ON button on the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.

DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner’s manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Declaration of conformity

EIKI PROJECTOR, MODEL EIP-1000T

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

EIKI INTERNATIONAL, INC.

30251 Esperanza Rancho Santa Margarita, CA 92688-2132 TEL: 800-242-3454

U.S.A. ONLY

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 50.

This EIKI projector uses a DMD panel. This very sophisticated panel contains 409,920 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

2

Page 4 Page 6
Image 5
Page 4 Page 6
Contents EIP-1000T If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Eiki PROJECTOR, Model EIP-1000TEiki INTERNATIONAL, INC For Future Reference Using the Menu ScreenContents Reference Maintenance Maintenance Indicators Regarding the LampAccessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function Optional accessory AccessoriesQCNWGA075WJPZ QACCDA007WJPZHeight 31 Adjust Focus ring For adjusting the focusLever 28, 48 Lamp indicator Part Names and FunctionExhaust vent Speaker Kensington Security Standard connector Rear adjustment FootPart Names and Functions Rear ViewBAR, Cinema Zoom Picture ModeAttach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range STANDBY-ON Setup and ProjectionQuick Start Upper side On the remote controlSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample Stretch Mode Picture Size Projection PRJ ModeScreen Size and Projection Distance When using a wide screen 169 and projecting 169 imageWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection Sub adaptor Connecting to Video EquipmentTo audio output Connecting to Video Equipment To INPUT1 terminal To Audio Terminal RGB Cable Connecting to a ComputerTo audio output terminal To RGB output terminal Computer Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Lamp indicator Power indicator STANDBY-ON button On button Connecting the Power CordTurning the Projector On/Off Turning the Projector onPress oSTANDBY-ON on the pro Projector into standby modeJector or eSTANDBY on the re Mote control, then press that butAdjusting the Projected Image Adjusting the Focus Switching the Input ModeAdjusting the Screen Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjust lever Make small adjustments Rear adjustment foot HeightScreen and turn off the sound Adjusting the VolumeAV Mute button Volume buttons Press P/Q or O/R to adjust Keystone Correction Press g Keystone to enter Keystone Correction modeCorrecting Trapezoidal Distortion Press g KeystonePress Hresize Resize ModeComputer Selecting the Picture Mode Operating with the Remote ControlAuto Sync Auto Sync Adjustment Freezing a Moving ImageInput 1 Component/INPUT Menu ItemsComponent/INPUT 3/INPUT Input 1 RGB/INPUT2 RGBHelp menu n Items you can set with Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press BmenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press hENTERExample Picture screen menu for Input 3 mode Picture Adjustment Picture menuMenu operation n 2Adjusting the ImageImage Adjusting the Projected Image SCR ADJ menuAdjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speed 3Auto Power Off FunctionPress Oor Qto select Help, then Troubleshooting with Help menuUtilizing Help menu functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsRed on Internal Blocked air intake Relocate the projector to Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer GND Connecting Pin AssignmentsSVGA, XGA, SXGA, SXGA+ Computer Compatibility Chart23-27 TroubleshootingAn input signal type Picture is pink no green Product type Projector Model EIP-1000T Video system SpecificationsDimensions Stretch IndexSide BAR Index Eastern Europe CanadaDeutschland & Österreich Japan & Worldwide
Top Page Image Contents