Eiki EIP-1000T owner manual Introduction, A. only

Page 4
U.S.A. ONLY

Before using the projector, please read this owner’s manual carefully.

Introduction

ENGLISH

1.WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2.CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED

WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead sym- bol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

1

Image 4
Contents EIP-1000T This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage Introduction A. onlyEiki INTERNATIONAL, INC Eiki PROJECTOR, Model EIP-1000TEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Using the Menu Screen For Future ReferenceContents Maintenance Maintenance Indicators Regarding the Lamp ReferenceCleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Accessories Optional accessoryQCNWGA075WJPZ QACCDA007WJPZFocus ring For adjusting the focus Height 31 AdjustLever 28, 48 Lamp indicator Part Names and FunctionRear adjustment Foot Exhaust vent Speaker Kensington Security Standard connectorPart Names and Functions Rear ViewPicture Mode BAR, Cinema ZoomInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Quick Start Setup and ProjectionSTANDBY-ON On the remote control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Stretch Mode Picture SizeWhen using a wide screen 169 and projecting 169 image Screen Size and Projection DistanceWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection To audio output Connecting to Video EquipmentSub adaptor Connecting to Video Equipment To audio output terminal To RGB output terminal Computer Connecting to a ComputerTo INPUT1 terminal To Audio Terminal RGB Cable Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Connecting the Power Cord Lamp indicator Power indicator STANDBY-ON button On buttonTurning the Projector On/Off Turning the Projector onProjector into standby mode Press oSTANDBY-ON on the proJector or eSTANDBY on the re Mote control, then press that butSwitching the Input Mode Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot HeightAV Mute button Volume buttons Adjusting the VolumeScreen and turn off the sound Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeComputer Operating with the Remote Control Selecting the Picture ModeAuto Sync Auto Sync Adjustment Freezing a Moving ImageMenu Items Input 1 Component/INPUTComponent/INPUT 3/INPUT Input 1 RGB/INPUT2 RGBItems you can set with Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 3 mode2Adjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ menu ImageAdjusting the Projector Function PRJ ADJ menu 3Auto Power Off Function This function changes the fan rotation speedUtilizing Help menu functions Troubleshooting with Help menuPress Oor Qto select Help, then Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorRed on Internal Blocked air intake Relocate the projector to Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments GNDComputer Compatibility Chart SVGA, XGA, SXGA, SXGA+Troubleshooting 23-27An input signal type Picture is pink no green Specifications Product type Projector Model EIP-1000T Video systemDimensions Side BAR IndexStretch Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide