Eiki EIP-1000T Rest your eyes occasionally, Avoid locations with extremes of tem- perature

Page 11

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

Potential hazard of glass par-

ticles if lamp ruptures. In case of lamp rupture, contact your nearest EIKI Authorized Dealer or Service Center for replacement.

See “Replacing the Lamp” on page 50.

Caution concerning the setup of the pro- jector

For minimal servicing and to maintain high image quality, EIKI recommends that this pro- jector be installed in an area free from hu- midity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more of- ten. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a EIKI Authorized Dealer or Service Cen- ter.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)

When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

Warning about placing the projector in a high position

When placing the projector in a high position, ensure that it is secured carefully to avoid per- sonal injury caused by the projector falling down.

Do not subject the projector to hard im- pact and/or vibration.

Protect the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

Continuously watching the screen for long hours will cause eye strain. Be sure to occa- sionally rest your eyes.

Do not set up the projector in places ex- posed to direct sunlight or bright light.

Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projec- tor

Place the projector on a level site within the adjustment range (8 degrees) of the adjust- ment foot.

Avoid locations with extremes of tem- perature.

The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

Be sure that the intake vent and the exhaust vent are not obstructed.

If the cooling fan becomes obstructed, a pro- tection circuit will automatically put the pro- jector into standby mode to prevent overheat damage. This does not indicate a malfunc- tion. (See pages 48 and 49.) Remove the pro- jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

8

Image 11
Contents EIP-1000T If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Eiki PROJECTOR, Model EIP-1000TEiki INTERNATIONAL, INC For Future Reference Using the Menu ScreenContents Reference Maintenance Maintenance Indicators Regarding the LampPower-Cord Protection CleaningAccessories Power SourcesOverloading Damage Requiring ServiceReplacement Parts Safety CheckDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function QACCDA007WJPZ AccessoriesOptional accessory QCNWGA075WJPZPart Names and Function Focus ring For adjusting the focusHeight 31 Adjust Lever 28, 48 Lamp indicatorRear View Rear adjustment FootExhaust vent Speaker Kensington Security Standard connector Part Names and FunctionsBAR, Cinema Zoom Picture ModeAttach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range STANDBY-ON Setup and ProjectionQuick Start Upper side On the remote controlCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionExample Stretch Mode Picture Size Projection PRJ ModeScreen Size and Projection Distance When using a wide screen 169 and projecting 169 imageWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection Sub adaptor Connecting to Video EquipmentTo audio output Connecting to Video Equipment To INPUT1 terminal To Audio Terminal RGB Cable Connecting to a ComputerTo audio output terminal To RGB output terminal Computer Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Turning the Projector on Connecting the Power CordLamp indicator Power indicator STANDBY-ON button On button Turning the Projector On/OffMote control, then press that but Projector into standby modePress oSTANDBY-ON on the pro Jector or eSTANDBY on the reImage Projection Switching the Input ModeAdjusting the Projected Image Adjusting the Focus Adjusting the Screen SizeHeight Adjusting the HeightUse the rear adjustment foot to make the projector level Adjust lever Make small adjustments Rear adjustment footScreen and turn off the sound Adjusting the VolumeAV Mute button Volume buttons Press g Keystone Press g Keystone to enter Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionPress Hresize Resize ModeComputer Freezing a Moving Image Operating with the Remote ControlSelecting the Picture Mode Auto Sync Auto Sync AdjustmentInput 1 RGB/INPUT2 RGB Menu ItemsInput 1 Component/INPUT Component/INPUT 3/INPUTHelp menu n Items you can set with Help menuPress Bmenu Using the Menu ScreenMenu Selections Adjustments Press Q or O and select Picture to adjustPress hENTER To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedExample Picture screen menu for Input 3 mode Picture Adjustment Picture menuMenu operation n 2Adjusting the ImageImage Adjusting the Projected Image SCR ADJ menuAdjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speed 3Auto Power Off FunctionPress Oor Qto select Help, then Troubleshooting with Help menuUtilizing Help menu functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsRed on Internal Blocked air intake Relocate the projector to Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer GND Connecting Pin AssignmentsSVGA, XGA, SXGA, SXGA+ Computer Compatibility Chart23-27 TroubleshootingAn input signal type Picture is pink no green Product type Projector Model EIP-1000T Video system SpecificationsDimensions Stretch IndexSide BAR Index Japan & Worldwide CanadaEastern Europe Deutschland & Österreich