Eiki EIP-1000T owner manual Upper side, On the remote control

Page 20

Zoom ring

• When using the remote control, press the 4 button to switch the INPUT mode.

On the remote control

S INPUT 3

• When pressing the INPUT button on the projector, input mode switches in the following order: INPUT1 INPUT2 INPUT3 INPUT4

On-screen display

On the projector

Select the “INPUT 3” using the INPUT button on the projector or D INPUT 3 on the remote control.

4. Turn the video equipment on and start playback

5. Select the INPUT mode

CINPUT 1/CINPUT 2/DINPUT 3/EINPUT

_P. 30

6. Adjust the focus, image size, and projector angle

1.Adjust the focus by turning the focus ring.

2.Adjust the projection image size by turning the zoom ring.

3.Adjust the projector angle using the HEIGHT ADJUST lever.

Focus ring

_PP. 30, 31

7. Correct trapezoidal distortion

Correcting trapezoidal distortion using the Keystone Correction.

On the projector

Shrinks	Shrinks
upper side.	lower side.

On the remote control

_P. 33

8. Turn the Power off

Press the STANDBY-ON button on the projector or the STANDBY button on the remote control, and then press the button again while the confirmation message is displayed, to put the projector into standby mode.

On the	On the remote	On-screen Display
On the	On the remote
projector	control
• Unplug the power cord from the AC outlet after the cooling fan stops.			_P. 29

17

Image 20

Contents EIP-1000T This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage Introduction A. onlyEsperanza Rancho Santa Margarita, CA 92688-2132 TEL Eiki PROJECTOR, Model EIP-1000TEiki INTERNATIONAL, INC Using the Menu Screen For Future ReferenceContents Maintenance Maintenance Indicators Regarding the Lamp ReferenceCleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoryQCNWGA075WJPZ QACCDA007WJPZFocus ring For adjusting the focus Height 31 AdjustLever 28, 48 Lamp indicator Part Names and FunctionRear adjustment Foot Exhaust vent Speaker Kensington Security Standard connectorPart Names and Functions Rear ViewPicture Mode BAR, Cinema ZoomInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range STANDBY-ON Setup and ProjectionQuick Start On the remote control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Stretch Mode Picture SizeWhen using a wide screen 169 and projecting 169 image Screen Size and Projection DistanceWhen using a normal screen 43 and projecting 169 image Samples of Cables for Connection Sub adaptor Connecting to Video EquipmentTo audio output Connecting to Video Equipment To INPUT1 terminal To Audio Terminal RGB Cable Connecting to a ComputerTo audio output terminal To RGB output terminal Computer Connecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio Equipment Connecting the Power Cord Lamp indicator Power indicator STANDBY-ON button On buttonTurning the Projector On/Off Turning the Projector onProjector into standby mode Press oSTANDBY-ON on the proJector or eSTANDBY on the re Mote control, then press that butSwitching the Input Mode Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot HeightScreen and turn off the sound Adjusting the VolumeAV Mute button Volume buttons Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeComputer Operating with the Remote Control Selecting the Picture ModeAuto Sync Auto Sync Adjustment Freezing a Moving ImageMenu Items Input 1 Component/INPUTComponent/INPUT 3/INPUT Input 1 RGB/INPUT2 RGBItems you can set with Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 3 mode2Adjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ menu ImageAdjusting the Projector Function PRJ ADJ menu 3Auto Power Off Function This function changes the fan rotation speedPress Oor Qto select Help, then Troubleshooting with Help menuUtilizing Help menu functions Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorRed on Internal Blocked air intake Relocate the projector to Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Connecting Pin Assignments GNDComputer Compatibility Chart SVGA, XGA, SXGA, SXGA+Troubleshooting 23-27An input signal type Picture is pink no green Specifications Product type Projector Model EIP-1000T Video systemDimensions Stretch IndexSide BAR Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide