Intel SBC-780 manual Usb

Page 12

F u l l-S i z e C P U C a r d	S B C - 7 8 0







Power supply voltage	+5V (4.75V to 5.25V), +12V (11.4V to
	12.6V), -5V (-4.75V to -5.25V), -12V
	(-11.4V to –12.6V), ATX/AT
Size / Weight	13.3” (L) x 4.8” (W) (338mm x 122mm)
	1.2lb (0.5kg)

Operating temperature 32 F to 140 F (0 C to 60 C)

I/O

















Enhanced IDE	ATA-100 x 2 channel
Interface	(support 4 ATAPI devices)
FDD Interface	Standard FDD port x 1
	(supports up to 2 floppy devices)
Serial Ports	COM1: RS-232
	COM2: RS-232/RS-422/RS-485
Parallel Port	supports SPP/EPP/ECP mode
Keyboard / PS2	Mini-DIN for PS/2 K/B and mouse
Mouse connector	connector x 1
	Internal keyboard pin header x 1
	Internal mouse pin header x 1
IrDA	One IrDA Tx/Rx header
Audio	Realtek ALC201 AC97 multi-channel
	codec
USB	Two 5x2 pin headers
	(support 4 USB 1.1 ports)

Chapter 1 General Information

1 - 5

Image 12

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications SystemUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of JumpersConnectors List of ConnectorsDIMM1 Setting Jumpers Open ClosedLCD Voltage Selection JP2 Tftlcd Clock Selection JP3COM2 RS-232/422/485 Selection JP6&JP7 Clear Cmos JP8 PCI-104 I/O Voltage Selection JP1012 COM2 Ring/+5V/+12V Selection JP11 Optional ATX Power Connector CN1 Ttllcd Connector CN2Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5USB1 Connector CN8 USB2 Connector CN9SIR Connector CN6 USB Connectors CN8/CN9LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN1525 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Keyboard Connector CN22 Internal Mouse Connector CN23Audio Input/Output Connector CN24 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin SignalFront Panel Connector JP5 IDE LED IDE LED+Award Bios Setup System test and initialization  Entering setup  Major Setup Features Advanced Features Setup  Main Standard Cmos Features Default Load Optimized Defaults  Security Password PC Health Setup  Clk/Voltage Setup  Save & Exit Setup Exit  Exit Without Saving Standard Cmos setup Main Setup Date and Time Configuration  IDE Primary/Secondary Master/Slave  IDE HDD Auto-Detection IDE Primary/Secondary Master/Slave  Drive a  Drive B Video  Halt On Select Display Device  Base MemoryAdvanced Features Setup  Quick Power On Self Test  First/Second/Third Boot Device Virus Warning  Boot Other Device  Boot Up Floppy Seek Boot Up NumLock Status  Swap Floppy Drive Typematic Rate Setting  Typematic Delay Msec Gate A20 Option  Typematic Rate Chars/Sec Video Bios Shadow  Security Option OS Select For Dram 64MB  Advanced Chipset features setup  Dram Timing By SPD Memory Hole  Frame Buffer Size Boot Device Select  AGP Aperture Size Panel Type  OnChip USB IDE Prefetch Mode  Integrated Peripherals OnChip IDE Channel0 / OnChip IDE Channel1  Primary/Secondary Master/Slave PIO  Primary/Secondary Master/Slave Udma Init Display First  Onboard LAN1/LAN2 IDE HDD Block Mode  Uart 2 Mode Onboard Serial Port 1/ Port  IR Function Duplex Tx, Rx inverting enable  Onboard Parallel Mode ECP Mode Use DMA  Onboard Parallel Port Sound Blaster  SB I/O Base Address SB IRQ Select  SB DMA Select Power Management Setup  Power Management Acpi Function  PM Control by APM  Video off Option Video off Method  Modem Use IRQ State After Power Failure This option will not be availa Ble when AT power is Applied Soft-Off by Pwrbtn  PCI Master  Date of Month  Resume Time hhmmss  Primay IntrChoices Enabled, Disabled  PnP/PCI Configuration  PNP OS Installed Reset Configuration Data PCI/ISA PnP  Resources Controlled By IRQ Resources  DMA Resources PCI/VGA Palette Snoop  Assign IRQ For VGA Assign IRQ For USB  Load Optimized Defaults Default Setup Set/Change password Security Setup CPU Warning Temperature  Shutdown Temperature Power on show status PC Health Setup CPU fan low speed warning 6 Clk/Voltage Setup  Auto Detect DIMM/PCI CLK Spread Spectrum  Save & Exit Setup Exit Setup Exit without saving Driver Installation Please follow the sequence below to install the drivers Cd-rom \Driver\ Install VIA 4-in-1 DriverApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Reset ProgrammingCompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash CardC 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicatedPull the cover hard from the reverse corner indicated