Intel SBC-780 manual  Sound Blaster,  SB I/O Base Address,  SB IRQ Select,  SB DMA Select

Page 58

F u l l - Size CPU Card	S B C - 7 8 0

Sound Blaster

Enable to utilize Sound Blaster function.

The choices: Disabled, Enabled

SB I/O Base Address

Select a base I/O address for the Sound Blaster interface. The choices: 220H, 240H, 260H, 280H

SB IRQ Select

Select Interrupt for the Sound Blaster interface.

The choices: IRQ 5, IRQ 7, IRQ 9, IRQ 10

SB DMA Select

Select DMA mode for the Sound Blaster interface.

The choices: DMA 0, DMA 1, DMA 2, DMA 3

Chapter3 Award BIOS Setup

3 - 20

Image 58

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications SystemUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of JumpersConnectors List of ConnectorsDIMM1 Setting Jumpers Open ClosedTftlcd Clock Selection JP3 LCD Voltage Selection JP2COM2 RS-232/422/485 Selection JP6&JP7 PCI-104 I/O Voltage Selection JP10 Clear Cmos JP812 COM2 Ring/+5V/+12V Selection JP11 Optional ATX Power Connector CN1 Ttllcd Connector CN2Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5SIR Connector CN6 USB1 Connector CN8USB2 Connector CN9 USB Connectors CN8/CN9LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN1525 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Mouse Connector CN23 Internal Keyboard Connector CN22Audio Input/Output Connector CN24 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin SignalFront Panel Connector JP5 IDE LED IDE LED+Award Bios Setup System test and initialization  Advanced Features Setup  Entering setup Major Setup Features  Main Standard Cmos Features Security Password  Default Load Optimized Defaults PC Health Setup  Exit  Clk/Voltage Setup Save & Exit Setup  Exit Without SavingMain Setup  Standard Cmos setup Date and Time Configuration  IDE Primary/Secondary Master/Slave  IDE Primary/Secondary Master/Slave IDE HDD Auto-Detection  Drive a  Drive B Select Display Device  Video Halt On  Base MemoryAdvanced Features Setup  First/Second/Third Boot Device  Quick Power On Self Test Virus Warning  Boot Up NumLock Status  Boot Other Device Boot Up Floppy Seek  Swap Floppy Drive Gate A20 Option  Typematic Rate Setting Typematic Delay Msec  Typematic Rate Chars/Sec Security Option  Video Bios Shadow OS Select For Dram 64MB  Memory Hole  Advanced Chipset features setup Dram Timing By SPD  Frame Buffer Size Panel Type  Boot Device Select AGP Aperture Size  OnChip USB Integrated Peripherals  IDE Prefetch Mode OnChip IDE Channel0 / OnChip IDE Channel1  Init Display First  Primary/Secondary Master/Slave PIO Primary/Secondary Master/Slave Udma  Onboard LAN1/LAN2 Onboard Serial Port 1/ Port  IDE HDD Block Mode Uart 2 Mode  IR Function Duplex ECP Mode Use DMA  Tx, Rx inverting enable Onboard Parallel Mode  Onboard Parallel Port SB IRQ Select  Sound Blaster SB I/O Base Address  SB DMA Select Power Management  Power Management Setup Acpi Function  Video off Method  PM Control by APM Video off Option  Modem Use IRQThis option will not be availa Ble when AT power is Applied  State After Power Failure Soft-Off by Pwrbtn  PCI Master  Date of Month  Resume Time hhmmss  Primay IntrChoices Enabled, Disabled  PNP OS Installed  PnP/PCI Configuration Reset Configuration Data  IRQ Resources PCI/ISA PnP Resources Controlled By  DMA Resources Assign IRQ For VGA  PCI/VGA Palette Snoop Assign IRQ For USB  Load Optimized Defaults Default Setup Set/Change password Security Setup Power on show status  CPU Warning Temperature Shutdown Temperature PC Health Setup CPU fan low speed warning  Auto Detect DIMM/PCI CLK 6 Clk/Voltage Setup Spread Spectrum Exit Setup  Save & Exit Setup Exit without saving Driver Installation Cd-rom \Driver\ Install VIA 4-in-1 Driver Please follow the sequence below to install the driversApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Reset ProgrammingCompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash CardC 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicatedPull the cover hard from the reverse corner indicated