Intel SBC-780 manual  Gate A20 Option,  Typematic Rate Setting,  Typematic Rate Chars/Sec

Page 50

F u l l - Size CPU Card

S B C - 7 8 0

 

 

Gate A20 Option

Gate A20 refers to the way the system addresses memory above 1 MB (extended memory). When set to Fast, the system chipset controls Gate A20. When set to Normal, a pin in the keyboard controller controls Gate A20. Setting Gate A20 to fast improves system speed, particularly with OS/2 and Windows.

The choices: Fast, Normal.

Typematic Rate Setting

Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected.

The choices: Enabled, Disabled.

Typematic Rate (Chars/Sec)

When the typematic rate setting is enabled, you can sel ect a

typematic rate , at which character repeats when

you hold

down a key.

 

The choices: 6, 8, 10, 12, 15, 20, 24, 30.

Typematic Delay (Msec)

When the typematic rate setting is enabled, you can select a typematic delay, at which before keystrokes begin to repeat.

The choices: 250, 500, 750, 1000

Chapter3 Award BIOS Setup

3 - 12

Image 50
Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications SystemUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of JumpersConnectors List of ConnectorsDIMM1 Setting Jumpers Open ClosedCOM2 RS-232/422/485 Selection JP6&JP7 LCD Voltage Selection JP2Tftlcd Clock Selection JP3 12 COM2 Ring/+5V/+12V Selection JP11 Clear Cmos JP8PCI-104 I/O Voltage Selection JP10 Optional ATX Power Connector CN1 Ttllcd Connector CN2Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5SIR Connector CN6 USB1 Connector CN8USB2 Connector CN9 USB Connectors CN8/CN9LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN1525 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Audio Input/Output Connector CN24 Internal Keyboard Connector CN22Internal Mouse Connector CN23 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin SignalFront Panel Connector JP5 IDE LED IDE LED+Award Bios Setup System test and initialization  Advanced Features Setup  Entering setup Major Setup Features  Main Standard Cmos Features PC Health Setup  Default Load Optimized Defaults Security Password  Exit  Clk/Voltage Setup Save & Exit Setup  Exit Without Saving Date and Time Configuration  Standard Cmos setupMain Setup  IDE Primary/Secondary Master/Slave  IDE Primary/Secondary Master/Slave IDE HDD Auto-Detection  Drive a  Drive B Select Display Device  Video Halt On  Base MemoryAdvanced Features Setup  Virus Warning  Quick Power On Self Test First/Second/Third Boot Device  Boot Up NumLock Status  Boot Other Device Boot Up Floppy Seek  Swap Floppy Drive Gate A20 Option  Typematic Rate Setting Typematic Delay Msec  Typematic Rate Chars/Sec OS Select For Dram 64MB  Video Bios Shadow Security Option  Memory Hole  Advanced Chipset features setup Dram Timing By SPD  Frame Buffer Size Panel Type  Boot Device Select AGP Aperture Size  OnChip USB OnChip IDE Channel0 / OnChip IDE Channel1  IDE Prefetch Mode Integrated Peripherals  Init Display First  Primary/Secondary Master/Slave PIO Primary/Secondary Master/Slave Udma  Onboard LAN1/LAN2 Onboard Serial Port 1/ Port  IDE HDD Block Mode Uart 2 Mode  IR Function Duplex ECP Mode Use DMA  Tx, Rx inverting enable Onboard Parallel Mode  Onboard Parallel Port SB IRQ Select  Sound Blaster SB I/O Base Address  SB DMA Select Acpi Function  Power Management Setup Power Management  Video off Method  PM Control by APM Video off Option  Modem Use IRQ Soft-Off by Pwrbtn  State After Power FailureThis option will not be availa Ble when AT power is Applied  PCI Master  Date of Month  Resume Time hhmmss  Primay IntrChoices Enabled, Disabled  Reset Configuration Data  PnP/PCI Configuration PNP OS Installed  IRQ Resources PCI/ISA PnP Resources Controlled By  DMA Resources Assign IRQ For USB  PCI/VGA Palette Snoop Assign IRQ For VGA  Load Optimized Defaults Default Setup Set/Change password Security Setup Power on show status  CPU Warning Temperature Shutdown Temperature PC Health Setup CPU fan low speed warning  Spread Spectrum 6 Clk/Voltage Setup Auto Detect DIMM/PCI CLK  Exit without saving  Save & Exit SetupExit Setup Driver Installation Applicable for Windows 2000/98/ME/XP Please follow the sequence below to install the driversCd-rom \Driver\ Install VIA 4-in-1 Driver C 7 8 Programming Watchdog Timer Reset ProgrammingCompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash CardC 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicatedPull the cover hard from the reverse corner indicated