Intel SBC-780 manual PCI/ISA PnP,  Resources Controlled By,  IRQ Resources,  DMA Resources

Page 65

F u l l - Size CPU Card

S B C - 7 8 0

 

 

Resources Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all the boot and Plug and Play device s. If you choose Auto, you cannot select IRQ DMA and memory base address fields, since BIOS automatically assigns them.

The choices: Auto (ESCD), Manual.

IRQ Resources

When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the

interrupt. There are two types for choice:

Legacy ISA and

PCI/ISA PnP.

 

Legacy ISA: Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1)

PCI/ISA PnP: Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.

DMA Resources

When resources are controlled manually, assign each DMA channel a type, depending on the type of device using the DMA channel. There are two ty pes for choice: Legacy ISA and

PCI/ISA PnP.

Legacy ISA: Devices compliant with the original PC AT bus specification, requiring a specific DMA channel

PCI/ISA PnP: Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.

Chapter3 Award BIOS Setup

3 - 27

Image 65
Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System SpecificationsUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers JumpersList of Connectors ConnectorsDIMM1 Open Closed Setting JumpersCOM2 RS-232/422/485 Selection JP6&JP7 LCD Voltage Selection JP2Tftlcd Clock Selection JP3 12 COM2 Ring/+5V/+12V Selection JP11 Clear Cmos JP8PCI-104 I/O Voltage Selection JP10 Ttllcd Connector CN2 Optional ATX Power Connector CN1Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4USB2 Connector CN9 USB1 Connector CN8SIR Connector CN6 USB Connectors CN8/CN921 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN1325 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Audio Input/Output Connector CN24 Internal Keyboard Connector CN22Internal Mouse Connector CN23 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2IDE LED IDE LED+ Front Panel Connector JP5Award Bios Setup System test and initialization  Major Setup Features  Entering setup Advanced Features Setup  Main Standard Cmos Features PC Health Setup  Default Load Optimized Defaults Security Password  Save & Exit Setup  Clk/Voltage Setup Exit  Exit Without Saving Date and Time Configuration  Standard Cmos setupMain Setup  IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave IDE Primary/Secondary Master/Slave  Drive a  Drive B Halt On  Video Select Display Device  Base MemoryAdvanced Features Setup  Virus Warning  Quick Power On Self Test First/Second/Third Boot Device  Boot Up Floppy Seek  Boot Other Device Boot Up NumLock Status  Swap Floppy Drive Typematic Delay Msec  Typematic Rate Setting Gate A20 Option  Typematic Rate Chars/Sec OS Select For Dram 64MB  Video Bios Shadow Security Option  Dram Timing By SPD  Advanced Chipset features setup Memory Hole  Frame Buffer Size AGP Aperture Size  Boot Device Select Panel Type  OnChip USB OnChip IDE Channel0 / OnChip IDE Channel1  IDE Prefetch Mode Integrated Peripherals  Primary/Secondary Master/Slave Udma  Primary/Secondary Master/Slave PIO Init Display First  Onboard LAN1/LAN2 Uart 2 Mode  IDE HDD Block Mode Onboard Serial Port 1/ Port  IR Function Duplex Onboard Parallel Mode  Tx, Rx inverting enable ECP Mode Use DMA  Onboard Parallel Port SB I/O Base Address  Sound Blaster SB IRQ Select  SB DMA Select Acpi Function  Power Management Setup Power Management  Video off Option  PM Control by APM Video off Method  Modem Use IRQ Soft-Off by Pwrbtn  State After Power FailureThis option will not be availa Ble when AT power is Applied  Date of Month  Resume Time hhmmss  Primay Intr  PCI MasterChoices Enabled, Disabled  Reset Configuration Data  PnP/PCI Configuration PNP OS Installed  Resources Controlled By PCI/ISA PnP IRQ Resources  DMA Resources Assign IRQ For USB  PCI/VGA Palette Snoop Assign IRQ For VGA Default Setup  Load Optimized DefaultsSecurity Setup  Set/Change password Shutdown Temperature  CPU Warning Temperature Power on show status PC Health Setup CPU fan low speed warning  Spread Spectrum 6 Clk/Voltage Setup Auto Detect DIMM/PCI CLK  Exit without saving  Save & Exit SetupExit Setup Driver Installation Applicable for Windows 2000/98/ME/XP Please follow the sequence below to install the driversCd-rom \Driver\ Install VIA 4-in-1 Driver C 7 8 Programming Watchdog Timer Programming ResetCompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash coverC 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash coverPull the cover hard from the reverse corner indicated