Intel SBC-780 manual  Soft-Off by Pwrbtn,  State After Power Failure

Page 61

F u l l - Size CPU Card	S B C - 7 8 0

Soft-Off by PWRBTN

The choices: Delay 4 Sec, Instant-off

State After Power Failure

This field lets you determine the state that your PC returns to after a power failure. If set to off, the PC will not boot after a power failure. If set to on, the PC will restart after a power failure. If set to auto, the PC will restart to the former status.

This option will not be availa	ble when AT power is
applied.

The choices: Auto, On, Off

Wake Up Events

VGA

The choices: Off, On

LPT & COM

The choices: NONE, LPT, COM, LPT/COM

Chapter3 Award BIOS Setup

3 - 23

Image 61

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System SpecificationsUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers JumpersList of Connectors ConnectorsDIMM1 Open Closed Setting JumpersTftlcd Clock Selection JP3 LCD Voltage Selection JP2COM2 RS-232/422/485 Selection JP6&JP7 PCI-104 I/O Voltage Selection JP10 Clear Cmos JP812 COM2 Ring/+5V/+12V Selection JP11 Ttllcd Connector CN2 Optional ATX Power Connector CN1Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4USB2 Connector CN9 USB1 Connector CN8SIR Connector CN6 USB Connectors CN8/CN921 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN1325 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Mouse Connector CN23 Internal Keyboard Connector CN22Audio Input/Output Connector CN24 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2IDE LED IDE LED+ Front Panel Connector JP5Award Bios Setup System test and initialization  Major Setup Features  Entering setup Advanced Features Setup  Main Standard Cmos Features Security Password  Default Load Optimized Defaults PC Health Setup  Save & Exit Setup  Clk/Voltage Setup Exit  Exit Without SavingMain Setup  Standard Cmos setup Date and Time Configuration  IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave IDE Primary/Secondary Master/Slave  Drive a  Drive B Halt On  Video Select Display Device  Base MemoryAdvanced Features Setup  First/Second/Third Boot Device  Quick Power On Self Test Virus Warning  Boot Up Floppy Seek  Boot Other Device Boot Up NumLock Status  Swap Floppy Drive Typematic Delay Msec  Typematic Rate Setting Gate A20 Option  Typematic Rate Chars/Sec Security Option  Video Bios Shadow OS Select For Dram 64MB  Dram Timing By SPD  Advanced Chipset features setup Memory Hole  Frame Buffer Size AGP Aperture Size  Boot Device Select Panel Type  OnChip USB Integrated Peripherals  IDE Prefetch Mode OnChip IDE Channel0 / OnChip IDE Channel1  Primary/Secondary Master/Slave Udma  Primary/Secondary Master/Slave PIO Init Display First  Onboard LAN1/LAN2 Uart 2 Mode  IDE HDD Block Mode Onboard Serial Port 1/ Port  IR Function Duplex Onboard Parallel Mode  Tx, Rx inverting enable ECP Mode Use DMA  Onboard Parallel Port SB I/O Base Address  Sound Blaster SB IRQ Select  SB DMA Select Power Management  Power Management Setup Acpi Function  Video off Option  PM Control by APM Video off Method  Modem Use IRQThis option will not be availa Ble when AT power is Applied  State After Power Failure Soft-Off by Pwrbtn  Date of Month  Resume Time hhmmss  Primay Intr  PCI MasterChoices Enabled, Disabled  PNP OS Installed  PnP/PCI Configuration Reset Configuration Data  Resources Controlled By PCI/ISA PnP IRQ Resources  DMA Resources Assign IRQ For VGA  PCI/VGA Palette Snoop Assign IRQ For USB Default Setup  Load Optimized DefaultsSecurity Setup  Set/Change password Shutdown Temperature  CPU Warning Temperature Power on show status PC Health Setup CPU fan low speed warning  Auto Detect DIMM/PCI CLK 6 Clk/Voltage Setup Spread Spectrum Exit Setup  Save & Exit Setup Exit without saving Driver Installation Cd-rom \Driver\ Install VIA 4-in-1 Driver Please follow the sequence below to install the driversApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Programming ResetCompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash coverC 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash coverPull the cover hard from the reverse corner indicated