Intel SBC-780 manual  Primary/Secondary Master/Slave PIO,  Primary/Secondary Master/Slave Udma

Page 55

F u l l - Size CPU Card	S B C - 7 8 0

Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmable Input Output) fields let you set a PIO mode for each of the tow IDE devices and the two storage devices that the onboard IDE interface supports. Modes 0 to 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.

The choices: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode

4

Primary/Secondary Master/Slave UDMA

Ultra DMA33/66/100 implementation is only working when your IDE hard drive supports it and the operating environment includes a DMA driver. If your hard drive and IDE cable both support Ultra DMA 33/66/100 select Auto to enable BIOS support.

The choices: Auto, Disabled

Init Display First

You can select AGP or PCI slot to initialize it as the primary display before initializing any other display device on the system.

The choices: PCI Slot, AGP

Onboard LAN1/LAN2

The default setting for this is “Enabled”. If you do not utilize onboard LAN function, just configure it as “Disabled” without any efforts on jumper setting.

The choices: Enabled, Disabled

Chapter3 Award BIOS Setup

3 - 17

Image 55

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System SpecificationsUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers JumpersList of Connectors ConnectorsDIMM1 Open Closed Setting JumpersTftlcd Clock Selection JP3 LCD Voltage Selection JP2COM2 RS-232/422/485 Selection JP6&JP7 PCI-104 I/O Voltage Selection JP10 Clear Cmos JP812 COM2 Ring/+5V/+12V Selection JP11 Ttllcd Connector CN2 Optional ATX Power Connector CN1Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4USB Connectors CN8/CN9 USB1 Connector CN8USB2 Connector CN9 SIR Connector CN621 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN1325 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Mouse Connector CN23 Internal Keyboard Connector CN22Audio Input/Output Connector CN24 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2IDE LED IDE LED+ Front Panel Connector JP5Award Bios Setup System test and initialization  Main Standard Cmos Features  Entering setup Major Setup Features  Advanced Features Setup Security Password  Default Load Optimized Defaults PC Health Setup  Exit Without Saving  Clk/Voltage Setup Save & Exit Setup  ExitMain Setup  Standard Cmos setup Date and Time Configuration  Drive a  Drive B  IDE Primary/Secondary Master/Slave IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave Base Memory  Video Halt On  Select Display DeviceAdvanced Features Setup  First/Second/Third Boot Device  Quick Power On Self Test Virus Warning  Swap Floppy Drive  Boot Other Device Boot Up Floppy Seek  Boot Up NumLock Status Typematic Rate Chars/Sec  Typematic Rate Setting Typematic Delay Msec  Gate A20 Option Security Option  Video Bios Shadow OS Select For Dram 64MB  Frame Buffer Size  Advanced Chipset features setup Dram Timing By SPD  Memory Hole OnChip USB  Boot Device Select AGP Aperture Size  Panel Type Integrated Peripherals  IDE Prefetch Mode OnChip IDE Channel0 / OnChip IDE Channel1  Onboard LAN1/LAN2  Primary/Secondary Master/Slave PIO Primary/Secondary Master/Slave Udma  Init Display First IR Function Duplex  IDE HDD Block Mode Uart 2 Mode  Onboard Serial Port 1/ Port Onboard Parallel Port  Tx, Rx inverting enable Onboard Parallel Mode  ECP Mode Use DMA SB DMA Select  Sound Blaster SB I/O Base Address  SB IRQ Select Power Management  Power Management Setup Acpi Function  Modem Use IRQ  PM Control by APM Video off Option  Video off MethodThis option will not be availa Ble when AT power is Applied  State After Power Failure Soft-Off by Pwrbtn  Date of Month  Resume Time hhmmss  Primay Intr  PCI MasterChoices Enabled, Disabled  PNP OS Installed  PnP/PCI Configuration Reset Configuration Data  DMA Resources PCI/ISA PnP Resources Controlled By  IRQ Resources Assign IRQ For VGA  PCI/VGA Palette Snoop Assign IRQ For USB Default Setup  Load Optimized DefaultsSecurity Setup  Set/Change passwordPC Health Setup  CPU Warning Temperature Shutdown Temperature  Power on show status CPU fan low speed warning  Auto Detect DIMM/PCI CLK 6 Clk/Voltage Setup Spread Spectrum Exit Setup  Save & Exit Setup Exit without saving Driver Installation Cd-rom \Driver\ Install VIA 4-in-1 Driver Please follow the sequence below to install the driversApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Programming ResetCompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash coverC 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash coverPull the cover hard from the reverse corner indicated