Intel SBC-780 manual  Standard Cmos setup, Main Setup,  Date and Time Configuration

Page 44

F u l l - Size CPU Card

S B C - 7 8 0

 

 

3.2.1Main Setup

Standard CMOS setup

Select [Main] for STANDARD CMOS SETUP option from the top menu, the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the right box of the Menu screen.

Date and Time Configuration

The BIOS determines the day of the week from the other date information. This field is for information only.

Press the le ft or right arrow key to move to the desired field (date, month, year). Press the PgUp/- or PgDn/+ key to change the setting, or type the desired value into the field.

The time format is based on the 24 -hour military -time clock. For example, 1 p.m. is 13: 00:00 hours. Press the left or right arrow key to move to the desired field. Press the PgUp/ - or PgDn/+ key to change the setting, or type the desired value into the field.

Chapter3 Award BIOS Setup

3 - 6

Image 44
Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications SystemUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of JumpersConnectors List of ConnectorsDIMM1 Setting Jumpers Open ClosedCOM2 RS-232/422/485 Selection JP6&JP7 LCD Voltage Selection JP2Tftlcd Clock Selection JP3 12 COM2 Ring/+5V/+12V Selection JP11 Clear Cmos JP8PCI-104 I/O Voltage Selection JP10 Optional ATX Power Connector CN1 Ttllcd Connector CN2Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5USB1 Connector CN8 USB2 Connector CN9SIR Connector CN6 USB Connectors CN8/CN9LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN1525 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Audio Input/Output Connector CN24 Internal Keyboard Connector CN22Internal Mouse Connector CN23 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin SignalFront Panel Connector JP5 IDE LED IDE LED+Award Bios Setup System test and initialization  Entering setup  Major Setup Features Advanced Features Setup  Main Standard Cmos Features PC Health Setup  Default Load Optimized Defaults Security Password  Clk/Voltage Setup  Save & Exit Setup Exit  Exit Without Saving Date and Time Configuration  Standard Cmos setupMain Setup  IDE Primary/Secondary Master/Slave  IDE HDD Auto-Detection IDE Primary/Secondary Master/Slave  Drive a  Drive B Video  Halt On Select Display Device  Base MemoryAdvanced Features Setup  Virus Warning  Quick Power On Self Test First/Second/Third Boot Device  Boot Other Device  Boot Up Floppy Seek Boot Up NumLock Status  Swap Floppy Drive Typematic Rate Setting  Typematic Delay Msec Gate A20 Option  Typematic Rate Chars/Sec OS Select For Dram 64MB  Video Bios Shadow Security Option  Advanced Chipset features setup  Dram Timing By SPD Memory Hole  Frame Buffer Size Boot Device Select  AGP Aperture Size Panel Type  OnChip USB OnChip IDE Channel0 / OnChip IDE Channel1  IDE Prefetch Mode Integrated Peripherals  Primary/Secondary Master/Slave PIO  Primary/Secondary Master/Slave Udma Init Display First  Onboard LAN1/LAN2 IDE HDD Block Mode  Uart 2 Mode Onboard Serial Port 1/ Port  IR Function Duplex Tx, Rx inverting enable  Onboard Parallel Mode ECP Mode Use DMA  Onboard Parallel Port Sound Blaster  SB I/O Base Address SB IRQ Select  SB DMA Select Acpi Function  Power Management Setup Power Management  PM Control by APM  Video off Option Video off Method  Modem Use IRQ Soft-Off by Pwrbtn  State After Power FailureThis option will not be availa Ble when AT power is Applied  PCI Master  Date of Month  Resume Time hhmmss  Primay IntrChoices Enabled, Disabled  Reset Configuration Data  PnP/PCI Configuration PNP OS Installed PCI/ISA PnP  Resources Controlled By IRQ Resources  DMA Resources Assign IRQ For USB  PCI/VGA Palette Snoop Assign IRQ For VGA  Load Optimized Defaults Default Setup Set/Change password Security Setup CPU Warning Temperature  Shutdown Temperature Power on show status PC Health Setup CPU fan low speed warning  Spread Spectrum 6 Clk/Voltage Setup Auto Detect DIMM/PCI CLK  Exit without saving  Save & Exit SetupExit Setup Driver Installation Applicable for Windows 2000/98/ME/XP Please follow the sequence below to install the driversCd-rom \Driver\ Install VIA 4-in-1 Driver C 7 8 Programming Watchdog Timer Reset ProgrammingCompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash CardC 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicatedPull the cover hard from the reverse corner indicated