Intel SBC-780 manual Ttllcd Connector CN3

Page 27

	F u l l - Size CPU Card			S B C - 7 8 0


29	R02	30		R03

31	R04	32		R05

33	GND	34		GND

35	DOT_CLOCK	36		VSYNC

37	DE	38		HSYNC

39	N.C	40		ENAVEE

2.15 TTL_LCD Connector (CN3)

Pin	Signal	Pin	Signal
1	GND	2	GND

3	B10	4	B11

5	B12	6	B13

7	B14	8	B15

9	G10	10	G11

11	G12	12	G13

13	G14	14	G15

15	R10	16	R11

17	R12	18	R13

19	R14	20	R15

Chapter 2 Quick Installation Guide

2 - 14

Image 27

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System SpecificationsUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers JumpersList of Connectors ConnectorsDIMM1 Open Closed Setting JumpersLCD Voltage Selection JP2 Tftlcd Clock Selection JP3COM2 RS-232/422/485 Selection JP6&JP7 Clear Cmos JP8 PCI-104 I/O Voltage Selection JP1012 COM2 Ring/+5V/+12V Selection JP11 Ttllcd Connector CN2 Optional ATX Power Connector CN1Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4USB Connectors CN8/CN9 USB1 Connector CN8USB2 Connector CN9 SIR Connector CN621 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN1325 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Keyboard Connector CN22 Internal Mouse Connector CN23Audio Input/Output Connector CN24 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2IDE LED IDE LED+ Front Panel Connector JP5Award Bios Setup System test and initialization  Main Standard Cmos Features  Entering setup Major Setup Features  Advanced Features Setup Default Load Optimized Defaults  Security Password PC Health Setup  Exit Without Saving  Clk/Voltage Setup Save & Exit Setup  Exit Standard Cmos setup Main Setup Date and Time Configuration  Drive a  Drive B  IDE Primary/Secondary Master/Slave IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave Base Memory  Video Halt On  Select Display DeviceAdvanced Features Setup  Quick Power On Self Test  First/Second/Third Boot Device Virus Warning  Swap Floppy Drive  Boot Other Device Boot Up Floppy Seek  Boot Up NumLock Status Typematic Rate Chars/Sec  Typematic Rate Setting Typematic Delay Msec  Gate A20 Option Video Bios Shadow  Security Option OS Select For Dram 64MB  Frame Buffer Size  Advanced Chipset features setup Dram Timing By SPD  Memory Hole OnChip USB  Boot Device Select AGP Aperture Size  Panel Type IDE Prefetch Mode  Integrated Peripherals OnChip IDE Channel0 / OnChip IDE Channel1  Onboard LAN1/LAN2  Primary/Secondary Master/Slave PIO Primary/Secondary Master/Slave Udma  Init Display First IR Function Duplex  IDE HDD Block Mode Uart 2 Mode  Onboard Serial Port 1/ Port Onboard Parallel Port  Tx, Rx inverting enable Onboard Parallel Mode  ECP Mode Use DMA SB DMA Select  Sound Blaster SB I/O Base Address  SB IRQ Select Power Management Setup  Power Management Acpi Function  Modem Use IRQ  PM Control by APM Video off Option  Video off Method State After Power Failure This option will not be availa Ble when AT power is Applied Soft-Off by Pwrbtn  Date of Month  Resume Time hhmmss  Primay Intr  PCI MasterChoices Enabled, Disabled  PnP/PCI Configuration  PNP OS Installed Reset Configuration Data  DMA Resources PCI/ISA PnP Resources Controlled By  IRQ Resources PCI/VGA Palette Snoop  Assign IRQ For VGA Assign IRQ For USB Default Setup  Load Optimized DefaultsSecurity Setup  Set/Change passwordPC Health Setup  CPU Warning Temperature Shutdown Temperature  Power on show status CPU fan low speed warning 6 Clk/Voltage Setup  Auto Detect DIMM/PCI CLK Spread Spectrum  Save & Exit Setup Exit Setup Exit without saving Driver Installation Please follow the sequence below to install the drivers Cd-rom \Driver\ Install VIA 4-in-1 DriverApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Programming ResetCompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash coverC 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash coverPull the cover hard from the reverse corner indicated