Intel SBC-780 manual  PCI/VGA Palette Snoop,  Assign IRQ For VGA,  Assign IRQ For USB

Page 66

F u l l - Size CPU Card	S B C - 7 8 0

PCI/VGA Palette Snoop

Enabling this item informs the PCI VGA card to keep silent (and to prevent conflict) when palette register is updated (i.e., accepts data without responding any communication signals).

This is useful only when two display cards use the same palette address and plugged in the PCI bus at the same time (such as MPEG or Video capture card). In such case, PCI VGA is silent while MPEG/Video capture card is set to function normally.

The Choices: Enabled, Disabled

Assign IRQ For VGA

The Choices: Enabled, Disabled

Assign IRQ For USB

The Choices: Enabled, Disabled

Chapter3 Award BIOS Setup

3 - 28

Image 66

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications SystemUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of JumpersConnectors List of ConnectorsDIMM1 Setting Jumpers Open ClosedLCD Voltage Selection JP2 Tftlcd Clock Selection JP3COM2 RS-232/422/485 Selection JP6&JP7 Clear Cmos JP8 PCI-104 I/O Voltage Selection JP1012 COM2 Ring/+5V/+12V Selection JP11 Optional ATX Power Connector CN1 Ttllcd Connector CN2Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5SIR Connector CN6 USB1 Connector CN8USB2 Connector CN9 USB Connectors CN8/CN9LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN1525 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Keyboard Connector CN22 Internal Mouse Connector CN23Audio Input/Output Connector CN24 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin SignalFront Panel Connector JP5 IDE LED IDE LED+Award Bios Setup System test and initialization  Advanced Features Setup  Entering setup Major Setup Features  Main Standard Cmos Features Default Load Optimized Defaults  Security Password PC Health Setup  Exit  Clk/Voltage Setup Save & Exit Setup  Exit Without Saving Standard Cmos setup Main Setup Date and Time Configuration  IDE Primary/Secondary Master/Slave  IDE Primary/Secondary Master/Slave IDE HDD Auto-Detection  Drive a  Drive B Select Display Device  Video Halt On  Base MemoryAdvanced Features Setup  Quick Power On Self Test  First/Second/Third Boot Device Virus Warning  Boot Up NumLock Status  Boot Other Device Boot Up Floppy Seek  Swap Floppy Drive Gate A20 Option  Typematic Rate Setting Typematic Delay Msec  Typematic Rate Chars/Sec Video Bios Shadow  Security Option OS Select For Dram 64MB  Memory Hole  Advanced Chipset features setup Dram Timing By SPD  Frame Buffer Size Panel Type  Boot Device Select AGP Aperture Size  OnChip USB IDE Prefetch Mode  Integrated Peripherals OnChip IDE Channel0 / OnChip IDE Channel1  Init Display First  Primary/Secondary Master/Slave PIO Primary/Secondary Master/Slave Udma  Onboard LAN1/LAN2 Onboard Serial Port 1/ Port  IDE HDD Block Mode Uart 2 Mode  IR Function Duplex ECP Mode Use DMA  Tx, Rx inverting enable Onboard Parallel Mode  Onboard Parallel Port SB IRQ Select  Sound Blaster SB I/O Base Address  SB DMA Select Power Management Setup  Power Management Acpi Function  Video off Method  PM Control by APM Video off Option  Modem Use IRQ State After Power Failure This option will not be availa Ble when AT power is Applied Soft-Off by Pwrbtn  PCI Master  Date of Month  Resume Time hhmmss  Primay IntrChoices Enabled, Disabled  PnP/PCI Configuration  PNP OS Installed Reset Configuration Data  IRQ Resources PCI/ISA PnP Resources Controlled By  DMA Resources PCI/VGA Palette Snoop  Assign IRQ For VGA Assign IRQ For USB  Load Optimized Defaults Default Setup Set/Change password Security Setup Power on show status  CPU Warning Temperature Shutdown Temperature PC Health Setup CPU fan low speed warning 6 Clk/Voltage Setup  Auto Detect DIMM/PCI CLK Spread Spectrum  Save & Exit Setup Exit Setup Exit without saving Driver Installation Please follow the sequence below to install the drivers Cd-rom \Driver\ Install VIA 4-in-1 DriverApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Reset ProgrammingCompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash CardC 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicatedPull the cover hard from the reverse corner indicated