Intel SBC-780 manual  Tx, Rx inverting enable,  Onboard Parallel Port,  Onboard Parallel Mode

Page 57

F u l l - Size CPU Card	S B C - 7 8 0

Tx, Rx inverting enable

Please consult with your IR peripheral documentation to select the correct setting of the TxD and RxD signals.

The choices: No, No; No, Yes; Yes, No; Yes, Yes

Onboard Parallel Port

Two bi-directional parallel ports.

The choices: Disabled, 3BC/IRQ7, 378/IRQ7, 278/IRQ5

Onboard Parallel Mode

Two bi-directional parallel ports.

The choices: Normal, EPP, ECP, ECP/EPP

ECP Mode Use DMA

Select a DMA channel for the port.

The choices: 1, 3

Parallel Port EPP Type

You can use this feature to choose which version of EPP to sue. For better performance, use EPP 1.9. But if you are facing connection issues, try to set it to EPP 1.7.

The choices: EPP1.9, EPP1.7

Onboard Legacy Audio

Enable to utilize onboard legacy audio function

The choices: Disabled, Enabled

Chapter3 Award BIOS Setup

3 - 19

Image 57

Contents SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System SpecificationsUSB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers JumpersList of Connectors ConnectorsDIMM1 Open Closed Setting JumpersLCD Voltage Selection JP2 Tftlcd Clock Selection JP3COM2 RS-232/422/485 Selection JP6&JP7 Clear Cmos JP8 PCI-104 I/O Voltage Selection JP1012 COM2 Ring/+5V/+12V Selection JP11 Ttllcd Connector CN2 Optional ATX Power Connector CN1Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4USB2 Connector CN9 USB1 Connector CN8SIR Connector CN6 USB Connectors CN8/CN921 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN1325 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Keyboard Connector CN22 Internal Mouse Connector CN23Audio Input/Output Connector CN24 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2IDE LED IDE LED+ Front Panel Connector JP5Award Bios Setup System test and initialization  Major Setup Features  Entering setup Advanced Features Setup  Main Standard Cmos Features Default Load Optimized Defaults  Security Password PC Health Setup  Save & Exit Setup  Clk/Voltage Setup Exit  Exit Without Saving Standard Cmos setup Main Setup Date and Time Configuration  IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave IDE Primary/Secondary Master/Slave  Drive a  Drive B Halt On  Video Select Display Device  Base MemoryAdvanced Features Setup  Quick Power On Self Test  First/Second/Third Boot Device Virus Warning  Boot Up Floppy Seek  Boot Other Device Boot Up NumLock Status  Swap Floppy Drive Typematic Delay Msec  Typematic Rate Setting Gate A20 Option  Typematic Rate Chars/Sec Video Bios Shadow  Security Option OS Select For Dram 64MB  Dram Timing By SPD  Advanced Chipset features setup Memory Hole  Frame Buffer Size AGP Aperture Size  Boot Device Select Panel Type  OnChip USB IDE Prefetch Mode  Integrated Peripherals OnChip IDE Channel0 / OnChip IDE Channel1  Primary/Secondary Master/Slave Udma  Primary/Secondary Master/Slave PIO Init Display First  Onboard LAN1/LAN2 Uart 2 Mode  IDE HDD Block Mode Onboard Serial Port 1/ Port  IR Function Duplex Onboard Parallel Mode  Tx, Rx inverting enable ECP Mode Use DMA  Onboard Parallel Port SB I/O Base Address  Sound Blaster SB IRQ Select  SB DMA Select Power Management Setup  Power Management Acpi Function  Video off Option  PM Control by APM Video off Method  Modem Use IRQ State After Power Failure This option will not be availa Ble when AT power is Applied Soft-Off by Pwrbtn  Date of Month  Resume Time hhmmss  Primay Intr  PCI MasterChoices Enabled, Disabled  PnP/PCI Configuration  PNP OS Installed Reset Configuration Data  Resources Controlled By PCI/ISA PnP IRQ Resources  DMA Resources PCI/VGA Palette Snoop  Assign IRQ For VGA Assign IRQ For USB Default Setup  Load Optimized DefaultsSecurity Setup  Set/Change password Shutdown Temperature  CPU Warning Temperature Power on show status PC Health Setup CPU fan low speed warning 6 Clk/Voltage Setup  Auto Detect DIMM/PCI CLK Spread Spectrum  Save & Exit Setup Exit Setup Exit without saving Driver Installation Please follow the sequence below to install the drivers Cd-rom \Driver\ Install VIA 4-in-1 DriverApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Programming ResetCompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash coverC 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash coverPull the cover hard from the reverse corner indicated