Liebert XDP 8.0 S

Specifications

33

8.0 SPECIFICATIONS

Table 17 Liebert XDP160 specifications

Models XDP160RC--1 XDP160RA--1 XDP160RM--1

Cooling Capacity, Nominal

160kW / 46 Tons, 60Hz 140kW / 40 Tons, 50Hz

Each capacity is based on 45ºF (7ºC) entering water temperature and

140gpm (530lpm) water flow rate. Capacity is reduced when glycol mixtures

are used in place of 100% water.

Minimum Load

The Liebert XDP’s minimum recommended operating load is 20% of system

nominal capacity. For example, a Liebert XDP160 60Hz system’s minimum

load would be 32 kW. Loading below this value can unfavorably affect system

operation. Consult factory for any loading below this recommendation.

Electrical Requirements

Input 208V/3ph/60Hz 460V/3/ph60Hz 380/415V/3ph/50Hz

Full Load Amps 4A 2.1A 2.3A

Dimensions, inches (mm)

Height – Unit only 78 (1981)

Height – As shipped 83 (2108)

Width 38 (965)

Depth 34 (864)

Weight, lb (kg)

Unit only 821 (372)

Shipping weight Domestic: 990 (449); Export: 1067 (484)

Installed, with refrigerant and

chilled water 1038 (471)

Pipe Connections

Refrigerant supply to Liebert XD

cooling module 1-1/8" OD, Cu

Refrigerant return from Liebert XD

cooling module 2-1/8" OD, Cu

Chilled water supply and return 2-5/8" OD, Cu

Control Valve 2-way, 2" nominal; 35 PSIG close off pressure rating;

150 PSIG maximum allowable pressure

Pressure Drop – Chilled Water

Side

20 psig (137kPa, 1.38bar), with 140 gpm (530lpm) water flow rate,

control valve fully open

Temperature Rise – Chilled

Water Side at rated flow, °F (°C) 8.0 (4.4) 6.9 (3.8)

Number of Liebert XD cooling units connected, maximum (minimum)

Liebert XDCF10 16 (4)

Liebert XDH20 8 (2)

Liebert XDH32 5 (1)

Liebert XDV8 20 (4)

Liebert XDV10 16 (4)

Liebert XDO16 10 (2)

Liebert XDO20 8 (2)

Cabinet Exterior Finish Black, matte finish, heat-fused powder coat

Operating Ambient

Temperature, Maximum, °F (°C) 86 (30)

Agency

Approvals CSA 60Hz CE 50Hz

Contents

Main GENERAL SAFETY GUIDELINES ! NOTICE Fluorinated Greenhouse Gas RequirementsEuropean Union R XD P 160 1 TABLE OF CONTENTS Page FIGURES TABL ES Page 1.0 PRODUCT DESCRIPTION 1.1 General Product Information Chilled Water 1.1.1 Product/System Description 1.2 Equipment Inspection 1.3 Equipment Handling 1.3.1 Handling With Skid 1.3.2 Removal from Skid Page 1.3.3 Removing Piano Jacks 1.4 Mechanical Considerations 1.4.1 Positioning the Liebert XDP Floor Cutout Dimensions Unit Dimensional Data Figure 8 Dimensions Figure 9 Piping access points Table 2 Unit piping outlet connection sizes, inches, OD Cu 1.5 Electrical Information 1.6 High Voltage Connections 1.6.1 Connecting High-Voltage Cables Disconnect Switch Status Lamps User Interface Front of Liebert XDP Page Page Field ConnectionsAll Units Field ConnectionsOptional for All Units 2.0 P 2.1 European Union Fluorinated Greenhouse Gas Requirements 2.2 Connection Sizes 2.2.1 Recommended Pipe Size 2.3 Liebert XDP Interconnection with Liebert XD Cooling Modules 2.4 Piping Installation Method 2.4.1 Bypass Flow Controller Piping 13 Figure 17 Bypass flow controller details, dimensions Figure 18 Bypass flow controller arrangement Figure 19 Bypass flow controller piping 7/8 (22mm) ID 4 (102mm) NOTICE 2.6 Checklist for Proper Installation 3.0 CHECKLIST FOR LIEBERT XDP STARTUP 3.1 Filling the Pumped CircuitR-134a Table 7 System refrigerant charge for the supply and return mains 3.1.1 Calculating Refrigerant ChargeExample 4.0 MICROPROCESSOR CONTROL 4.1 Feature Overview 4.1.1 Display 4.2 Controls 4.2.1 Feature Overview 4.3 Main Menu 4.3.1 Viewing or Changing Settings 4.3.2 SETPOINTS MIN TEMP SP HIGH CW TEMP HI AIR TEMP LOW AIR TEMP 4.3.6 TIME 4.3.7 DATE 4.3.8 SETUP OPERATION RESTART TIME DELAY C/F DEGREES PUMP WAIT TD PUMP OFF TD LEAD PUMP DPSWCH VALVE TIME 4.3.9 Password SecuritySETPT PASSWORD and SERVICE PASSWORD Change PasswordSETPT PASSWORD Change PasswordSERVICE PASSWORD 4.3.10 CALIBRATE SENSOR 4.3.11 ALARM ENABLE 4.3.12 ALARM TIME DELAY 4.3.13 COM ALARM ENABLE 4.3.14 CUSTOM ALARMS 4.3.15 CUSTOM TEXT 4.3.16 DIAGNOSTICS 5.0 ALARM DESCRIPTIONS AND SOLUTIONS 5.1 Alarm Descriptions 5.2 Red and Green Lamp Indicators 5.3 Alter Alarm Settings 5.3.1 Enable or Disable Alarms 5.3.2 Increase or Decrease Alarm Time Delays 5.4 System Shutdown Causes Unit Is Off By Refrig Sens Fail Unit Is Off By High CW Temp Unit Is Off By Pump Short Cycle Unit Is Off By Low Refrig Temp 6.0 T Table 16 Troubleshooting the XDP 7.0 M 7.1 Fluorinated Greenhouse Gas Requirements 8.0 S Table 17 Liebert XDP160 specifications Ensuring The High Availability 0f Mission-Critical Data And Applications. Technical Support / Service Locations