Intel SE7500WV2 manual Electromagnetic Compatibility Notices, Fcc Usa

Page 81

Electromagnetic Compatibility Notices

FCC (USA)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation

5200 N.E. Elam Young Parkway

Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. The customer is responsible for ensuring compliance of the modified product.

Only peripherals (computer input/output devices, terminals, printers, etc.) that comply with FCC Class A or B limits may be attached to this computer product. Operation with noncompliant peripherals is likely to result in interference to radio and TV reception.

All cables used to connect to peripherals must be shielded and grounded. Operation with cables, connected to peripherals, that are not shielded and grounded may result in interference to radio and TV reception.

INDUSTRY CANADA (ICES-003)

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled: “Digital Apparatus,” ICES-003 of the Canadian Department of Communications.

Regulator and Integration Information

81

Page 80 Page 82
Image 81
Page 80 Page 82
Contents Intel Server Board SE7500WV2 Product Guide Page Contents Upgrading Configuration Software and UtilitiesEquipment Log and Power Consumption Worksheets Solving ProblemsTechnical Reference Regulatory and Integration InformationTables FiguresServer Board Features Server Board FeaturesDescription Server Board VersionsServer Board Connector and Component Locations Server Board Connector and Component LocationsBack Panel Connectors Back Panel ConnectorsMemory ProcessorPCI Riser Slots VideoATA-100 Controller Scsi ControllerNetwork Controller NIC Connector and Status LEDsKeyboard and Mouse RJ-45 Serial PortRJ-45 Signal Rear Serial 2 Port Adapter Pin-outAbbreviation Baseboard Management Controller System ManagementField Replaceable Units and Sensor Data Records System Event LogPlatform Event Management Emergency Management Port Intel Server ManagementEMP and Serial Over LAN Using Passwords Intrusion Switch MonitoringSecurity Software LocksSecure Mode Software Security Features Summary of Software Security FeaturesBoot without keyboard Rearrange the Standoffs Installation ProceduresInstalling the Server Board Install the Server BoardInstalling Processors Install the Processor Retention BracketsLower the locking bar completely Installing the Heat Sink Installing the Heat Sink Clip Installing Memory Connect Cables Connecting CablesInstalling a Service Partition on the Server Optional Installing your Operating System Installing Intel Server ManagementInstalling Intel SMaRT Tool Tools and Supplies Needed UpgradingInstalling DIMMs Adding or Replacing a Processor ProcessorsLower the locking bar completely Installing the Heat Sink Removing a Processor Replacing the Back up BatteryReplacing the Back up Battery Intel Server Board SE7500WV2 Product Guide Service Partition Optional Configuration Software and UtilitiesConfiguration Utilities System Software Update SequenceHot Keys Power-On Self-Test PostHot Keys To Do ThisBios Setup If Bios Setup Is InaccessibleTemporarily Changing the Boot Device Priority Configuring the Adaptec AIC-7899 Scsi Adapter When to Run the Adaptec SCSISelect UtilityRunning the Adaptec SCSISelect Utility Running the SCSISelect UtilityRunning the Promise FastBuild Utility When to Run the Promise FastBuild UtilityDirect Platform Control DPC Console Running the Promise FastBuild UtilityDPC Console Modes of Operation Using the System Setup Utility Running the DPC ConsoleCreating SSU Diskettes Running the SSU Working with the SSU InterfaceCustomizing the SSU Interface Setting Passwords and Security Options Setting Boot Device PrioritySetting the Administrator Password Exiting the SSUSetting the User Password Setting Security OptionsViewing the System Event Log Viewing Sensor Data Records Viewing FRU InformationUpdating the Bios Updating System Firmware and BiosUpdating the Firmware Verifying the FirmwareSaving a Configuration Saving and Restoring the System ConfigurationRestoring a Configuration Setting Up Paging AlertsIntel Server Board SE7500WV2 Product Guide Setting Up LAN Alerts Setting Up Remote LAN Access Setting Up Remote Modem or Serial AccessManaging the Server Remotely Creating a Bootable Diskette Software UpdatesSoftware Update Package Recovering the BiosFirmware Update Utility Description Running the Firmware Update UtilityFRU/SDR Load Utility Description Command Command Line FormatWhat You Need to Do How You Use the FRU/SDR Load UtilityPrompting for Product Level FRU Information Intel Server Board SE7500WV2 Product Guide Resetting the System Solving ProblemsChecklist Initial System StartupAfter the System Has Been Running Correctly Running New Application SoftwareMonitoring Post More Problem Solving ProceduresVerifying Proper Operation of Key System Lights Confirming Loading of the Operating SystemSpecific Problems and Corrective Actions Power Light Does Not LightNo Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate ProperlyDiskette Drive Activity Light Does Not Light Problems with Application Software Problems with NetworkBootable CD-ROM Is Not Detected CD-ROM Drive Activity Light Does Not LightCannot Connect to a Server Add-in adapter stopped working without apparent causeIntel Server Board SE7500WV2 Product Guide Technical Reference What it does at system resetServer Board Jumpers Jumper NameDiagnostic LED Decoder Post Diagnostic LEDsPost Codes Code0Fh 2Bh Off 2Dh 82h Off Standard Post Error Messages and Codes Post Error Codes and MessagesError Code Error Message119 11A 11B 11E 120 121 140 141 142 143 144 145 146 Extended Post Error Messages and Codes Bootblock Error Beep Codes Bios Recovery Beep CodesBios Recovery Beep Codes Bootblock Error Beep CodesIntel Server Board SE7500WV2 Product Guide Regulatory and Integration Information Product Safety ComplianceProduct Regulatory Compliance Product EMC ComplianceProduct Regulatory Compliance Markings FCC USA Electromagnetic Compatibility NoticesBsmi Taiwan Europe CE Declaration of ConformityEquipment Log Equipment Log and Power Consumption WorksheetsSerial Number Date Installed Manufacturer NameModel Number Worksheet, Calculating DC Power Usage Calculating Power ConsumptionPower Usage Worksheet Current UsageWorksheet, Total Combined Power Used by the System Voltage level and total current V X a = WTotal Watts For each voltage level Index Intel Server Board SE7500WV2 Product Guide
Top Page Image Contents