Sanyo XG-705A owner manual Check Option items, Enter the message to attach the E-mail

Page 77

10. How to Use the PJ Controller

2.Check Option items

Check the conditions where you would choose the projector to send an alert message. Regarding the alert message, see samples below.

3.Enter the message to attach the E-mail.

The message typed here will be attached to the alert message.

Samples of Alert Message

* When the internal temperature is too high

TITLE: Message from projector

Projector Model Name: XX100

TCP/IP: 192.168.0.111 Projector Name:

It sends you following message.

✳The Projector lamp is turned off, because internal projector temperature is too high.

Wait for the Temperature Warning Indicator to be turned off, and then turn the Projector on again. If the Indicator continues flashing, check the air filter for dust accumulation.

“A” 21.5degrees centigrade”B” -13.7degrees centigrade”C” 51.6 degrees centigrade Temperature of Sensor B is too high.

Temperature of Sensor C is too high.

✳The Network projector let users know the information which thermal sensor “A,” “B,” or “C” inside the projector detected the abnormal temperature risen and so the projector was turned off. Please refer to the item “Check the status of projector” for the location of the sensors “A,” “B,” and “C,” and temperature (p.79). Also see the owner’s manual of the projector for further details.

*When the internal power is failed

TITLE: Message from projector

Projector Model Name: XX100

TCP/IP: 192.168.0.111 Projector Name:

It sends you the following message.

✳The Projector lamp is turned off, because projector power circuit is failed.

Unplug this projector from AC outlet and ask for servicing to qualified service personnel.

✳The Projector lamp was turned off, because the projector power is failed.

Unplug the projector from AC outlet and ask servicing to a qualified service personnel

* When the life of the lamp has been expired

TITLE: Message from projector

Projector Model Name: XX100

TCP/IP: 192.168.0.111 Projector Name:

It sends you the following message:

✳The life span of lamp is reached. Lamp replacement is required.

✳Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert e-mail will be sent every time turning on the projector.

*When the time to clean filter comes

Warning mail will be sent when the time to clean filter comes. Time is set in the Filter counter.

77

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Network Set-up Operation Federal Communication Commission Notice ComplianceTrademarks and Copyright Safety InstructionsTable of Contents Restart Advanced SetupModerator Function TerminologyRequired Operating Environment for Computers Operating Environment and ConfigurationDiffers according to the operating environment Network Specifications of the ProjectorPage About LAN Functions ChapterAbout LAN Functions LAN Functions and the FeaturesImage Projecting System via LAN Flow of Image TransferAn Example of the Connection LAN Connection Modes Operate the computer mouse with the remote control Page Setup Procedures Network Configuration has completed Setup ProceduresInstall the software on computers Installing the Software Setup Procedures Names and Functions of the Operation Screen Network Connection Standby Display Names and Functions of the Operation ScreenParts Names and Functions of the Screen NetworkModule ClientAdvanced Settings NetworkModule Moderator Page Wired LAN Configurations Connecting to the LAN Line Wired LAN ConfigurationsNetwork Environment Settings Setting ProcedureWired LAN Configurations Confirming the Operation Wired LAN Configurations User PIN Code Wired Factory Default See the menu aboveDNS Domain System Blank Password User PIN Code Factory Default Setting of the Wired LANPage Wireless LAN Configurations Attaching the USB Wireless LAN Adapter Wireless LAN ConfigurationsSetting the Network Environment Setting ProceduresWireless LAN Configurations Easy Setting Computer environment and Wireless LAN connection Wireless InformationWireless Factory Default Leap User Blank Password Wireless LAN Factory Default SettingsOperation of Network Viewer Configurations with BrowserBrowser Configuration Configurations with BrowserIntroduction Browser EnvironmentStarting up the Browser Information Screen of Wireless LAN Screen of Wired LANParameters and descriptions of Information Quick Setup One-byte characters. The name set here will be displayed on TCP / IP Password Wireless SettingReaches in ***hours up to ASCII220 characters MailHave entered is displayed as up to ASCII32 characters Admin PasswordUser PIN code Figure will be displayed as . The password consists Moderator Login PasswordMiscellaneous Wireless LAN set menu Wired LAN set menu Change Configuration SetRestart Project the Image via the Networks Project the Image via the Networks Use the Moderator Function Moderator Function Use the Moderator FunctionPreparation Procedure for Using the Moderator Function Preparation for Using the Moderator FunctionRegistration of the Moderator Setting the Moderator FunctionRegistration of the Clients Participants Unregister from Moderator Status How to Use the Moderator FunctionProject the Client’s Images Stop Projecting the Client’s ImagesHow to Use Network Viewer Mechanism of NetworkViewer and the Flow of the Signal How to Use Network ViewerWireless LAN Infrastructure Communication Mode Wireless LAN AdHoc Communication ModeFunctional Conditions of FTP Server Which Provides Images Wired LAN Communication ModeOperation Operating with the PJ Controller Projecting the ImageSpecify the FTP server to provide image data Operating with the Browser Refresh Operating with the projector Wireless LANSet timing to switch images in Auto play mode 3-240 sec Page How to Use the PJ Controller How to Operate How to Use the PJ ControllerInitial Settings Registering E-mail Address Mail SettingEnter the message to attach the E-mail Check Option itemsTurning on/off the projector Power & StatusCheck the status of the projector Input ControlPC adjustment System Adjustment Image Adjustment Screen Setting Select On to automatically set the PC adjustment Confirm the actual adjustment ServiceLoading the Set Select Set Number and name the settingSave the setting Set Multi Control Select projector input Appendix Wireless LAN Connection cannot be established TroubleshootingAppendix Computer cannot connect projectorsWEP Projector/PJ Controller cannot be turned on/off Cannot start up the browserNetwork Viewer does not work with the projector operation Speed of playing back images are very slowTerminology Setting up the IP address with arp + pingcommand Configuring WEP security with the projector Appendix KW6AC
Top Page Image Contents