Sanyo XG-705A owner manual Power & Status, Turning on/off the projector

Page 78

10. How to Use the PJ Controller

Power & Status

Click “Power & Status” on the main menu and configure each item.

1. Turning on/off the projector

Click Standby/ON buttons. When clicking the Standby button, the confirmation message will appear. Click OK to turn off the projector.

CAUTION: Projector cannot be turned on for approximately 90 seconds after it being turned off. When the display of “Power Status” changes from “On cooling down” to “ On”, click ON to turn on the projector.

Caution about turning on/off the projector via the networks

When you wish to turn on/off the projector via the networks, preset the projector as follows:

1.Select “Setting” from the Projector menu.

2.Select “Standby mode” from the Setting menu and set it as “Normal”.

If you set this function as Normal, the network part of the projector is constantly provided with power even if the projector is turned off. If you set this as Eco, then the network part will be turned off when you turn off the projector. Consequently, you cannot turn on/off the projector via the networks.

78

Image 78

Contents Network Set-up Operation Compliance Federal Communication Commission NoticeSafety Instructions Trademarks and CopyrightTable of Contents Moderator Function Advanced SetupRestart TerminologyOperating Environment and Configuration Required Operating Environment for ComputersNetwork Specifications of the Projector Differs according to the operating environmentPage Chapter About LAN FunctionsImage Projecting System via LAN LAN Functions and the FeaturesAbout LAN Functions Flow of Image TransferAn Example of the Connection LAN Connection Modes Operate the computer mouse with the remote control Page Setup Procedures Setup Procedures Install the software on computersNetwork Configuration has completed Installing the Software Setup Procedures Names and Functions of the Operation Screen Names and Functions of the Operation Screen Network Connection Standby DisplayNetworkModule Client Parts Names and Functions of the ScreenAdvanced Settings NetworkModule Moderator Page Wired LAN Configurations Network Environment Settings Wired LAN ConfigurationsConnecting to the LAN Line Setting ProcedureWired LAN Configurations Confirming the Operation Wired LAN Configurations Wired Factory Default See the menu above User PIN CodeFactory Default Setting of the Wired LAN DNS Domain System Blank Password User PIN CodePage Wireless LAN Configurations Setting the Network Environment Wireless LAN ConfigurationsAttaching the USB Wireless LAN Adapter Setting ProceduresWireless LAN Configurations Easy Setting Wireless Information Wireless Factory DefaultComputer environment and Wireless LAN connection Wireless LAN Factory Default Settings Leap User Blank PasswordConfigurations with Browser Operation of Network ViewerIntroduction Configurations with BrowserBrowser Configuration Browser EnvironmentStarting up the Browser Screen of Wireless LAN Screen of Wired LAN InformationParameters and descriptions of Information Quick Setup One-byte characters. The name set here will be displayed on TCP / IP Wireless Setting PasswordMail Reaches in ***hours up to ASCII220 charactersAdmin Password Have entered is displayed as up to ASCII32 charactersUser PIN code Moderator Login Password Figure will be displayed as . The password consistsMiscellaneous Change Configuration Set Wireless LAN set menu Wired LAN set menuRestart Project the Image via the Networks Project the Image via the Networks Use the Moderator Function Use the Moderator Function Moderator FunctionPreparation for Using the Moderator Function Preparation Procedure for Using the Moderator FunctionSetting the Moderator Function Registration of the ModeratorRegistration of the Clients Participants Project the Client’s Images How to Use the Moderator FunctionUnregister from Moderator Status Stop Projecting the Client’s ImagesHow to Use Network Viewer Wireless LAN Infrastructure Communication Mode How to Use Network ViewerMechanism of NetworkViewer and the Flow of the Signal Wireless LAN AdHoc Communication ModeWired LAN Communication Mode OperationFunctional Conditions of FTP Server Which Provides Images Projecting the Image Operating with the PJ ControllerSpecify the FTP server to provide image data Operating with the Browser Refresh Wireless LAN Operating with the projectorSet timing to switch images in Auto play mode 3-240 sec Page How to Use the PJ Controller How to Use the PJ Controller How to Operate Initial Settings Mail Setting Registering E-mail AddressCheck Option items Enter the message to attach the E-mailPower & Status Turning on/off the projectorCheck the status of the projector Control InputPC adjustment System Adjustment Image Adjustment Screen Setting Select On to automatically set the PC adjustment Service Confirm the actual adjustmentSelect Set Number and name the setting Save the setting SetLoading the Set Multi Control Select projector input Appendix Appendix TroubleshootingWireless LAN Connection cannot be established Computer cannot connect projectorsWEP Network Viewer does not work with the projector operation Cannot start up the browserProjector/PJ Controller cannot be turned on/off Speed of playing back images are very slowTerminology Setting up the IP address with arp + pingcommand Configuring WEP security with the projector Appendix KW6AC