Sanyo XG-705A owner manual Check the status of the projector

Page 79

10. How to Use the PJ Controller

2. Check the status of the projector

The following items can be checked on the Power & Status screen.

Parameter	Description
Accumulated lamp-use time	Display the accumulated time of lamp use in hour increment.
Accumulated projector-use time ....	Display the accumulated time of projector use in hour increment.
Power Status	Display the status of the projector’s lamp as follows:
	“On”, “Off”, “Standby”, “Power Saver”, “Mode/On cooling
	down”, “Temperature Error/On cooling down”, “On starting up”,
	“On power management operating”, “Temperature Error/Standby”.
Projector Condition	Display the projector’s condition as follows:
	“Normal”, “Temperature Error”, “Power Failure”.
Input Status	Display the following input status
Input	Display the selected input mode.
Selection	Display the selected input source mode.
Signal Status	Display the signal status.
Internal Temperature	Display the detected internal temperature of the projector.
	The icons A, B, and C stand for the thermal sensors inside the projector.
	If the internal temperature exceeds the certain point, each icon changes
	as below and let users know the error. Check the air filters and
	surrounding area of exhaust and intake vents of the projector.

Icon A, B, and C are located as follows:

A:Ambient temperature of the projector

B:Ambient temperature of the panel

C:Ambient temperature of the lamp

✳The ambient temperature of the projector may be shown a little higher than the actual temperature.

79

Image 79

Contents Network Set-up Operation Federal Communication Commission Notice ComplianceTrademarks and Copyright Safety InstructionsTable of Contents Terminology Advanced SetupRestart Moderator FunctionRequired Operating Environment for Computers Operating Environment and ConfigurationDiffers according to the operating environment Network Specifications of the ProjectorPage About LAN Functions ChapterFlow of Image Transfer LAN Functions and the FeaturesAbout LAN Functions Image Projecting System via LANAn Example of the Connection LAN Connection Modes Operate the computer mouse with the remote control Page Setup Procedures Install the software on computers Setup ProceduresNetwork Configuration has completed Installing the Software Setup Procedures Names and Functions of the Operation Screen Network Connection Standby Display Names and Functions of the Operation ScreenParts Names and Functions of the Screen NetworkModule ClientAdvanced Settings NetworkModule Moderator Page Wired LAN Configurations Setting Procedure Wired LAN ConfigurationsConnecting to the LAN Line Network Environment SettingsWired LAN Configurations Confirming the Operation Wired LAN Configurations User PIN Code Wired Factory Default See the menu aboveDNS Domain System Blank Password User PIN Code Factory Default Setting of the Wired LANPage Wireless LAN Configurations Setting Procedures Wireless LAN ConfigurationsAttaching the USB Wireless LAN Adapter Setting the Network EnvironmentWireless LAN Configurations Easy Setting Wireless Factory Default Wireless InformationComputer environment and Wireless LAN connection Leap User Blank Password Wireless LAN Factory Default SettingsOperation of Network Viewer Configurations with BrowserBrowser Environment Configurations with BrowserBrowser Configuration IntroductionStarting up the Browser Information Screen of Wireless LAN Screen of Wired LANParameters and descriptions of Information Quick Setup One-byte characters. The name set here will be displayed on TCP / IP Password Wireless SettingReaches in ***hours up to ASCII220 characters MailHave entered is displayed as up to ASCII32 characters Admin PasswordUser PIN code Figure will be displayed as . The password consists Moderator Login PasswordMiscellaneous Wireless LAN set menu Wired LAN set menu Change Configuration SetRestart Project the Image via the Networks Project the Image via the Networks Use the Moderator Function Moderator Function Use the Moderator FunctionPreparation Procedure for Using the Moderator Function Preparation for Using the Moderator FunctionRegistration of the Moderator Setting the Moderator FunctionRegistration of the Clients Participants Stop Projecting the Client’s Images How to Use the Moderator FunctionUnregister from Moderator Status Project the Client’s ImagesHow to Use Network Viewer Wireless LAN AdHoc Communication Mode How to Use Network ViewerMechanism of NetworkViewer and the Flow of the Signal Wireless LAN Infrastructure Communication ModeOperation Wired LAN Communication ModeFunctional Conditions of FTP Server Which Provides Images Operating with the PJ Controller Projecting the ImageSpecify the FTP server to provide image data Operating with the Browser Refresh Operating with the projector Wireless LANSet timing to switch images in Auto play mode 3-240 sec Page How to Use the PJ Controller How to Operate How to Use the PJ ControllerInitial Settings Registering E-mail Address Mail SettingEnter the message to attach the E-mail Check Option itemsTurning on/off the projector Power & StatusCheck the status of the projector Input ControlPC adjustment System Adjustment Image Adjustment Screen Setting Select On to automatically set the PC adjustment Confirm the actual adjustment ServiceSave the setting Set Select Set Number and name the settingLoading the Set Multi Control Select projector input Appendix Computer cannot connect projectors TroubleshootingWireless LAN Connection cannot be established AppendixWEP Speed of playing back images are very slow Cannot start up the browserProjector/PJ Controller cannot be turned on/off Network Viewer does not work with the projector operationTerminology Setting up the IP address with arp + pingcommand Configuring WEP security with the projector Appendix KW6AC