Sanyo XG-705A owner manual Setting up the IP address with arp + pingcommand

Page 96

11. Appendix

Setting up the IP address with “arp” + “ping”command

You can use "arp" and "ping" command from Command Prompt to assign an IP address to your projector.

1.Start up projector and configure the Wired or Wireless LAN to communicate with the computer.

2.From Windows “Start” menu, click “Run”. In the field next to “Open:”, enter “command” and click OK. When “MS-DOS prompt” (or command prompt) appears, type in "arp" command as follows:

(Example)

C:\ > arp -s 169.254.1.100 00-c0-6f-05-1c-c2

Indicates an IP address you wish to assign to your projector.

Separates MAC address of your projector product every two characters by hyphen.

MAC address is indicated on a label attached to the bottom of each unit.

3.Next, enter "ping" command as follows: (Example)

C:\ > ping 169.254.1.100 (by executing ping command, the IP address will be set) Indicates an IP address you wish to assign to your projector.

Reply from 169.254.1.100:bytes=32 times=2ms TTL=255

(if this message appears, the IP address was successfully assigned to projector)

Note: The assigned IP address is saved in the firmware of projector, thus it will remain set even when the power is off. You can use the same method to re-assign an IP address.

If “arp+ping” option (“6, Configurations with Browser” ➔ “Advanced Setup” ➔ “TCP/IP” (p.46)) is disabled in TCP/IP setting of the projector, you cannot assign an IP address using "arp" and "ping" commands. (In factory default state, "arp+ping" is set to “Enable”).

96

Image 96

Contents Network Set-up Operation Compliance Federal Communication Commission NoticeSafety Instructions Trademarks and CopyrightTable of Contents Advanced Setup RestartModerator Function TerminologyOperating Environment and Configuration Required Operating Environment for ComputersNetwork Specifications of the Projector Differs according to the operating environmentPage Chapter About LAN FunctionsLAN Functions and the Features About LAN FunctionsImage Projecting System via LAN Flow of Image TransferAn Example of the Connection LAN Connection Modes Operate the computer mouse with the remote control Page Setup Procedures Setup Procedures Install the software on computersNetwork Configuration has completed Installing the Software Setup Procedures Names and Functions of the Operation Screen Names and Functions of the Operation Screen Network Connection Standby DisplayNetworkModule Client Parts Names and Functions of the ScreenAdvanced Settings NetworkModule Moderator Page Wired LAN Configurations Wired LAN Configurations Connecting to the LAN LineNetwork Environment Settings Setting ProcedureWired LAN Configurations Confirming the Operation Wired LAN Configurations Wired Factory Default See the menu above User PIN CodeFactory Default Setting of the Wired LAN DNS Domain System Blank Password User PIN CodePage Wireless LAN Configurations Wireless LAN Configurations Attaching the USB Wireless LAN AdapterSetting the Network Environment Setting ProceduresWireless LAN Configurations Easy Setting Wireless Information Wireless Factory DefaultComputer environment and Wireless LAN connection Wireless LAN Factory Default Settings Leap User Blank PasswordConfigurations with Browser Operation of Network ViewerConfigurations with Browser Browser ConfigurationIntroduction Browser EnvironmentStarting up the Browser Screen of Wireless LAN Screen of Wired LAN InformationParameters and descriptions of Information Quick Setup One-byte characters. The name set here will be displayed on TCP / IP Wireless Setting PasswordMail Reaches in ***hours up to ASCII220 charactersAdmin Password Have entered is displayed as up to ASCII32 charactersUser PIN code Moderator Login Password Figure will be displayed as . The password consistsMiscellaneous Change Configuration Set Wireless LAN set menu Wired LAN set menuRestart Project the Image via the Networks Project the Image via the Networks Use the Moderator Function Use the Moderator Function Moderator FunctionPreparation for Using the Moderator Function Preparation Procedure for Using the Moderator FunctionSetting the Moderator Function Registration of the ModeratorRegistration of the Clients Participants How to Use the Moderator Function Unregister from Moderator StatusProject the Client’s Images Stop Projecting the Client’s ImagesHow to Use Network Viewer How to Use Network Viewer Mechanism of NetworkViewer and the Flow of the SignalWireless LAN Infrastructure Communication Mode Wireless LAN AdHoc Communication ModeWired LAN Communication Mode OperationFunctional Conditions of FTP Server Which Provides Images Projecting the Image Operating with the PJ ControllerSpecify the FTP server to provide image data Operating with the Browser Refresh Wireless LAN Operating with the projectorSet timing to switch images in Auto play mode 3-240 sec Page How to Use the PJ Controller How to Use the PJ Controller How to OperateInitial Settings Mail Setting Registering E-mail AddressCheck Option items Enter the message to attach the E-mailPower & Status Turning on/off the projectorCheck the status of the projector Control InputPC adjustment System Adjustment Image Adjustment Screen Setting Select On to automatically set the PC adjustment Service Confirm the actual adjustmentSelect Set Number and name the setting Save the setting SetLoading the Set Multi Control Select projector input Appendix Troubleshooting Wireless LAN Connection cannot be establishedAppendix Computer cannot connect projectors WEP Cannot start up the browser Projector/PJ Controller cannot be turned on/offNetwork Viewer does not work with the projector operation Speed of playing back images are very slowTerminology Setting up the IP address with arp + pingcommand Configuring WEP security with the projector Appendix KW6AC