Hitachi CP-X608 user manual Image Menu, Over Scan, Position

Page 30

IMAGE Menu

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

/'07=4)$?

5'.'%6

 





2+%674'

#52'%6

+/#)'

18'45%#0

+0276

8215+6+10

5'672

*215+6+10

#7&+1

*2*#5'

5%4''0

*5+<'

126+10

#761#&,756':'%76'

/+7



 

'#5;/'07

 

 

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For an RGB or MIU signal

 

NORMAL ó 4:3 ó 16:9 ó SMALL

 

For an M1-D signal

ASPECT

NORMAL ó 4:3 ó 16:9 ó 14:9 ó SMALL

For a Video signal, S-video signal or Component video signal

 

 

4:3 ó 16:9 ó 14:9 ó SMALL

 

For no signal

 

4:3 (fixed)

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

Using the ▲/▼ buttons adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video and component signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

• Over-adjusting the vertical position may cause noise to appear on the screen. If this

V POSITION

occurs please reset the vertical position to the default setting. Pressing the RESET button

when the V POSITION is selected will reset the V POSITION to the default setting.

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal of 525i (480i) or 625i (576i), the range of this

 

adjustment depends on the OVER SCAN (above) setting. It is not

 

possible to adjust when the OVER SCAN is set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

• Over-adjusting the horizontal position may cause noise to appear on the screen. If this

H POSITION

occurs please reset the horizontal position to the default setting. Pressing the RESET

button when the H POSITION is selected will reset the H POSITION to the default setting.

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal of 525i (480i) or 625i (576i), the range of this

 

adjustment depends on the OVER SCAN (above) setting. It is not

 

possible to adjust when the OVER SCAN is set to 10.

(continued on next page)

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Contents of package Fastening the lens coverHOT!4 Part namesProjector HOTComponent Control panelRear panel 10 11 15 16Back Remote control Remote controlLaser Indicator 14 Laser pointer 14 It is a beam outletSetting up Suspended from the ceiling ArrangementOn a horizontal surface DownSecurity bar Anti-theft chain or wire Security slot Adjusting the projectors elevatorUsing the security bar and slot FootConnecting your devices Signal source Remote control SpeakersVCR/DVD player Connecting your devices About Plug-and-Play capabilityUSB Insert the Wireless Memory Network cardInserting an SD card and USB memory AUX I/O port SD card slot Angled cornerHow to use the slot cover lock Connecting power supplyAC inlet Connector of the power cord to the outlet Laser pointer Remote controlLaser Indicator Putting batteriesFront and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicatorOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSearching an input signal Selecting an input signalSelecting an aspect ratio Using the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal or s-video signalAdjusting the position Correcting the keystone distortionsUse the cursor buttons / to select Auto or Freezing the screen Using the magnify featurePress the on button of Magnify on the remote control Magnify indication will appear on the screenTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Enter buttonEasy Menu Easy Menu Picture Menu GammaCustom and then pressing the button or Using the / buttons switches the color temperature modePicture Menu Color TempMY Memory Active IrisLOAD1, LOAD2, LOAD3, LOAD4 SAVE1, SAVE2, SAVE3, SAVE4Image Menu Over ScanPosition Image Menu PhaseAuto Adjust Size3D-YCS Input MenuProgressive Color SpaceInput Menu ComponentM1-D Frame Lock RGBResolution Custom Resolution BOXSetup Menu Setup Menu Audio Menu Screen Menu Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Or keep no operation for about 10 secondsScreen Menu Start UPCapturing error has occurred. Please try again MyScreen registration is finishedMessage No Input is DetectedSync is OUT of Range Source NameAuto Search Option MenuTurn on  Turn OFF Auto onOption Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageLens Type Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordSecurity Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeDescription Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off BOXPC-LESS Live ModeMIU Menu PresentationSetup MIU MenuSubnet Mask Default GatewayIP Address Time DifferenceEncryption Network ModeMode SpeedRemove ALL, Remove SD CARD, Remove USB Lamp MaintenanceCase of replacement by yourself Type number = DT00771 Replacing the lampLamp warning LampType number = MU03642 Cleaning the air filter Air filterAir filter Internal clock battery Take the old battery outWill come up. Remove the battery Put a new battery Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationSpecifications
Top Page Image Contents