Hitachi CP-X608 user manual Description Security, Turning Off the PIN Lock Function

Page 51

OPTION Menu

2+0$1: +PRWV2+0%QFG

4)$

PIN BOX

2+0%QPHKTOCVKQP$1:

4)$

CONFIRMATION BOX

(PIN BOX)

OPTION Menu (continued)

Item

Description

SECURITY (continued)

3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/► /RGB and INPUT buttons.

A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration.

•If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are

displayed the menu will close. If necessary repeat the process from 3.1-1.

Afterwards, anytime the projector is restarted after

the power switch is turned off the PIN BOX will be displayed. Enter the registered PIN Code.

The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.

If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.

This function will activate only when the projector is started after the power switch was turned off.

•Please do not forget your PIN Code.

3.2 Turning Off the PIN LOCK Function

3.2-1 Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.

Enter the registered PIN Code to turn the PIN LOCK function off. If an incorrect PASSWORD is entered the menu will close.

3.3 If you have forgotten your PIN Code

3.3-1 While the PIN BOX is displayed, press and hold the RESET button for three seconds or press and hold the INPUT and ► buttons for three seconds. The 10 digit Inquiring Code will be displayed.

•If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off.

2+0$1: +PSWKTKPI%QFG

Inquiring Code

(PIN Code)

3.3-2 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.

(continued on next page)

51

Image 51

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Fastening the lens cover Contents of packageHOT Part namesProjector HOT!410 11 15 16 Control panelRear panel ComponentLaser pointer 14 It is a beam outlet Remote controlLaser Indicator 14 Back Remote controlSetting up Down ArrangementOn a horizontal surface Suspended from the ceilingFoot Adjusting the projectors elevatorUsing the security bar and slot Security bar Anti-theft chain or wire Security slotConnecting your devices Signal source Remote control SpeakersVCR/DVD player About Plug-and-Play capability Connecting your devicesAUX I/O port SD card slot Angled corner Insert the Wireless Memory Network cardInserting an SD card and USB memory USBHow to use the slot cover lock Connecting power supplyAC inlet Connector of the power cord to the outlet Putting batteries Remote controlLaser Indicator Laser pointerBack sensor About the remote control signalChanging the frequency of remote control signal Front and top sensorsUsing as a simple PC mouse & keyboard Using as a wired remote controlSTANDBY/ON button Power indicator Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSearching an input signal Selecting an input signalSelecting an aspect ratio  For a video signal or s-video signal Adjusting the zoom and focusAdjusting the lens shift Using the automatic adjustment featureAdjusting the position Correcting the keystone distortionsUse the cursor buttons / to select Auto or Magnify indication will appear on the screen Using the magnify featurePress the on button of Magnify on the remote control Freezing the screenTemporarily blanking the screen Enter button Using the menu functionEasy Menu Advanced MenuEasy Menu Easy Menu Gamma Picture MenuColor Temp Using the / buttons switches the color temperature modePicture Menu Custom and then pressing the button orSAVE1, SAVE2, SAVE3, SAVE4 Active IrisLOAD1, LOAD2, LOAD3, LOAD4 MY MemoryImage Menu Over ScanPosition Size PhaseAuto Adjust Image MenuColor Space Input MenuProgressive 3D-YCSInput Menu ComponentM1-D RGB Frame LockCustom Resolution BOX ResolutionSetup Menu Setup Menu Audio Menu Or keep no operation for about 10 seconds Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Screen MenuStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againSource Name No Input is DetectedSync is OUT of Range MessageAuto on Option MenuTurn on  Turn OFF Auto SearchOption Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageLens Type Remote Freq Factory ResetKEY Lock Remote ReceivSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off SecurityDescription Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function BOX Setting the Transition Detector offPresentation Live ModeMIU Menu PC-LESSMIU Menu SetupTime Difference Default GatewayIP Address Subnet MaskSpeed Network ModeMode EncryptionRemove ALL, Remove SD CARD, Remove USB Type number = DT00771 Replacing the lamp MaintenanceCase of replacement by yourself LampLamp Lamp warningAir filter Type number = MU03642 Cleaning the air filterAir filter Internal clock battery Take the old battery outWill come up. Remove the battery Put a new battery Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecification Warranty and after-serviceSpecifications