Hitachi CP-X608 user manual Power on/off, Turning on the power, Turning off the power

Page 17
Press the STANDBY/ON button on the projector or the remote control.

Power on/off

Power on/off

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position (marked “ I “).

The power indicator will light up in steady orange (66). Then wait several seconds because the buttons may not

3.function for these several seconds.

The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green.

STANDBY/ON button POWER indicator

Power

switch

To display the picture, select an input signal according to the section "Selecting an input signal" (19).

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position (marked “O“).

The POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

•Before turning the projector off, be sure to perform the REMOVE procedure using the SERVICE menu under the MIU menu if the SD card or USB memory is used (58).

•When the AUTO ON of the OPTION menu is set to the TURN ON, and the power was turned off by the power switch last time, only turning the power switch on makes the projection lamp light and makes the POWER indicator begin blinking (43).

•Use the shutdown switch (66) only when the projector is not turned off by normal procedure.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelComponent 10 11 15 16Laser Indicator 14 Remote controlBack Remote control Laser pointer 14 It is a beam outletSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootVCR/DVD player Connecting your devicesSignal source Remote control Speakers About Plug-and-Play capability Connecting your devicesInserting an SD card and USB memory Insert the Wireless Memory Network cardUSB AUX I/O port SD card slot Angled cornerAC inlet Connector of the power cord to the outlet How to use the slot cover lockConnecting power supply Laser Indicator Remote controlLaser pointer Putting batteriesChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicatorSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal or s-video signalUse the cursor buttons / to select Auto or Adjusting the positionCorrecting the keystone distortions Press the on button of Magnify on the remote control Using the magnify featureFreezing the screen Magnify indication will appear on the screenTemporarily blanking the screen Easy Menu Using the menu functionAdvanced Menu Enter buttonEasy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4Position Image MenuOver Scan Auto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceM1-D Input MenuComponent RGB Frame LockCustom Resolution BOX ResolutionSetup Menu Setup Menu Audio Menu Using the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againSync is OUT of Range No Input is DetectedMessage Source NameTurn on  Turn OFF Option MenuAuto Search Auto onLamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Lens Type GhostFilter Message KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionSecurity Registering the PIN CodeIf you have forgotten your PIN Code Description SecurityTurning Off the PIN Lock Function Turning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password BOX Setting the Transition Detector offMIU Menu Live ModePC-LESS PresentationMIU Menu SetupIP Address Default GatewaySubnet Mask Time DifferenceMode Network ModeEncryption SpeedRemove ALL, Remove SD CARD, Remove USB Case of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Lamp warningAir filter Type number = MU03642 Cleaning the air filterAir filter Will come up. Remove the battery Put a new battery Internal clock batteryTake the old battery out Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications
Top Page Image Contents