Hitachi CP-X608 Electrical power cord is not plugged, Power switch is not set to the on position

Page 68

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes

resolves your problem.

If the situation cannot be corrected,

2. The projector’s microprocessor may need to be reset. Please push the Shutdown switch by using a pin or

similar and the projector will be turned off immediately.

Before turning it again, wait at least 10 minutes to make the projector cool down enough.

3. Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the OPTION menu (47) to reset all settings to factory default.

Then, if the problem is not removed after the remedy, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

13

 

Correctly connect the power cord.

 

 

 

The power switch is not set to the on position.

17

 

Set the power switch to [ ] (On).

 

 

 

The main power source has been interrupted during

 

Power does not

operation such as by a power outage (blackout), etc.

17

Please turn the power off, and allow the projector to cool

come on.

down at least 2 minutes, then turn the power on again.

 

 

 

 

Either there is no lamp and/or lamp cover, or either

 

 

of these has not been properly fixed.

 

 

Please turn the power off, and allow the projector to cool down

59

 

at least 45 minutes. After the projector has sufficiently cooled

 

 

 

down, please make confirmation of the attachment state of the

 

 

lamp and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

Neither sounds

Signal source does not correctly work.

 

nor pictures are

Correctly set up the signal source device by referring to the

–

outputted.

manual of the source device.

 

 

The input changeover settings are mismatched.

18, 19

 

Select the input signal, and correct the settings.

 

 

68

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Contents of package Fastening the lens coverPart names ProjectorHOT!4 HOTControl panel Rear panelComponent 10 11 15 16Remote control Laser Indicator 14Back Remote control Laser pointer 14 It is a beam outletSetting up Arrangement On a horizontal surfaceSuspended from the ceiling DownAdjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot FootVCR/DVD player Connecting your devicesSignal source Remote control Speakers Connecting your devices About Plug-and-Play capabilityInsert the Wireless Memory Network card Inserting an SD card and USB memoryUSB AUX I/O port SD card slot Angled cornerAC inlet Connector of the power cord to the outlet How to use the slot cover lockConnecting power supply Remote control Laser IndicatorLaser pointer Putting batteriesAbout the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardPower on/off Turning on the powerTurning off the power STANDBY/ON button Power indicatorAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the zoom and focus Adjusting the lens shiftUsing the automatic adjustment feature  For a video signal or s-video signalUse the cursor buttons / to select Auto or Adjusting the positionCorrecting the keystone distortions Using the magnify feature Press the on button of Magnify on the remote controlFreezing the screen Magnify indication will appear on the screenTemporarily blanking the screen Using the menu function Easy MenuAdvanced Menu Enter buttonEasy Menu Easy Menu Picture Menu GammaUsing the / buttons switches the color temperature mode Picture MenuCustom and then pressing the button or Color TempActive Iris LOAD1, LOAD2, LOAD3, LOAD4MY Memory SAVE1, SAVE2, SAVE3, SAVE4Position Image MenuOver Scan Phase Auto AdjustImage Menu SizeInput Menu Progressive3D-YCS Color SpaceM1-D Input MenuComponent Frame Lock RGBResolution Custom Resolution BOXSetup Menu Setup Menu Audio Menu Using the /// buttons adjusts the menu position Using the / buttons switches the mode for the blank screenScreen Menu Or keep no operation for about 10 secondsScreen Menu Start UPCapturing error has occurred. Please try again MyScreen registration is finishedNo Input is Detected Sync is OUT of RangeMessage Source NameOption Menu Turn on  Turn OFFAuto Search Auto onLamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Lens Type GhostFilter Message Factory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function Description If you have forgotten your PasswordTurning on the MyScreen Password Setting the PasswordUsing the PIN Lock Function Turning the Password offSecurity Registering the PIN CodeIf you have forgotten your PIN Code Description SecurityTurning Off the PIN Lock Function Turning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off BOXLive Mode MIU MenuPC-LESS PresentationSetup MIU MenuDefault Gateway IP AddressSubnet Mask Time DifferenceNetwork Mode ModeEncryption SpeedRemove ALL, Remove SD CARD, Remove USB Maintenance Case of replacement by yourselfLamp Type number = DT00771 Replacing the lampLamp warning LampType number = MU03642 Cleaning the air filter Air filterAir filter Will come up. Remove the battery Put a new battery Internal clock batteryTake the old battery out Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workVolume is adjusted to an extremely low level Audio setting is not correctColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationSpecifications
Top Page Image Contents