Hitachi CP-X608 user manual Troubleshooting, Related messages, There is no input signal

Page 65

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status



 

of the signal source.

SYNC IS OUT OF RANGE

The horizontal or vertical frequency of the input signal

is not within the specified range.



fH kHz fV Hz

Please confirm the specs for your projector or the signal

 

source specs.

 

The internal temperature is rising.

 

Please turn the power off, and allow the projector to cool

 

down at least 20 minutes. After having confirmed the

 

following items, please turn the power ON again.

CHECK THE AIR FLOW

• Is there blockage of the air passage aperture?

 

• Is the air filter dirty?

 

• Does the peripheral temperature exceed 35°C?

 

If the same indication is displayed after the remedy, please set

 

FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

REMINDER

A note of precaution when cleaning the air filter.

***HRS PASSED AFTER THE Please immediately turn the power off, and clean or change

LAST FILTER CHECK.

the air filter referring to the “Air Filter” section of this manual

FILTER MAINTENANCE IS ESSENTIAL (61). After you have cleaned or changed the air filter,

TO REMOVE WARNING MESSAGE, please be sure to reset the filter timer (26, 62).

RESET FILTER TIMER.

 

SEE MANUAL FURTHER INFO.

 

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelComponent 10 11 15 16Laser Indicator 14 Remote controlBack Remote control Laser pointer 14 It is a beam outletSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootVCR/DVD player Connecting your devicesSignal source Remote control Speakers About Plug-and-Play capability Connecting your devicesInserting an SD card and USB memory Insert the Wireless Memory Network cardUSB AUX I/O port SD card slot Angled cornerAC inlet Connector of the power cord to the outlet How to use the slot cover lockConnecting power supply Laser Indicator Remote controlLaser pointer Putting batteriesChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicatorSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal or s-video signalUse the cursor buttons / to select Auto or Adjusting the positionCorrecting the keystone distortions Press the on button of Magnify on the remote control Using the magnify featureFreezing the screen Magnify indication will appear on the screenTemporarily blanking the screen Easy Menu Using the menu functionAdvanced Menu Enter buttonEasy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4Position Image MenuOver Scan Auto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceM1-D Input MenuComponent RGB Frame LockCustom Resolution BOX ResolutionSetup Menu Setup Menu Audio Menu Using the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againSync is OUT of Range No Input is DetectedMessage Source NameTurn on  Turn OFF Option MenuAuto Search Auto onLamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Lens Type GhostFilter Message KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionSecurity Registering the PIN CodeIf you have forgotten your PIN Code Description SecurityTurning Off the PIN Lock Function Turning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password BOX Setting the Transition Detector offMIU Menu Live ModePC-LESS PresentationMIU Menu SetupIP Address Default GatewaySubnet Mask Time DifferenceMode Network ModeEncryption SpeedRemove ALL, Remove SD CARD, Remove USB Case of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Lamp warningAir filter Type number = MU03642 Cleaning the air filterAir filter Will come up. Remove the battery Put a new battery Internal clock batteryTake the old battery out Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications
Top Page Image Contents